Handling help

lito · 06-30-2003, 11:48 AM

Drudis

Would you please take a look at these photos and tell me what you think on how the tires are put onto the ground.

http://dettagli.no-ip.com/turagua060...2694ModRez.jpg

http://dettagli.no-ip.com/turagua0603/DSCN2697.JPG

http://dettagli.no-ip.com/turagua0603/DSCN2731.JPG

The car is in it's almost stock weight, a fewer pound here and there but just a few.

Front: It has relocated bushings on stock front A-arms, 950-1050lbs H&R springs, koni yellows, middle setting and stock anti sway bar (1 5/1" if I not wrong)

Rear: MM Alum panhard, MM Torque Arm 390-430 lbs springs, cobra rear sway bar, koni yellows.

I forgot, it has 1.8 camber and 3.5 caster, toe is in it's stocks toe out limits, w/steeda camber plates. I know it may need a little more camber on temp readings that we got on the pyrometer.

I'm thinking on findind a better sway bars front/rear, what do you think?

blue00gt · 06-30-2003, 03:41 PM

It seems like your rear springs are a bit soft at 300 lb/in. If they are in the stock location, I would think that with the torque arm and the 1000 lb/in front springs that you would be getting understeer. Most folks recommend closer to 350 or 400 lb/in for that type of setup so that the rear will take on more cornering load.

lito · 06-30-2003, 05:23 PM

I might remind the number wrong, the springs where recommended by Chuck of MM given my current front springs, I'll check that out again.

lito · 06-30-2003, 07:37 PM

I was wrong, 390-430 lbs

blue00gt · 07-01-2003, 03:09 PM

Cool, that sounds more like the right rear spring rate for your combo. If you can get more positive caster with the plates you have I would put it up to 5 deg. or so. This will turn into more negative camber as you turn the wheel without causing extra uneven tire wear going straight.

lito · 07-01-2003, 04:50 PM

I'll have to take some material from shock towers. I'll do that.

Any other ideas?

pearlgt40 306 · 07-02-2003, 02:11 AM

do you have any other poly bushings? if so....then i would recommend an aftermarket anti-sway bar since it looks as though the car is rolling onto the outside wheel and lifting the inside.
...Energy Suspension Master Kit.. i have it. Works great.

pearlgt40 306 · 07-02-2003, 02:12 AM

beautiful fox by the way.

lito · 07-04-2003, 05:26 PM

I think I've found a 1 3/8" front bar, would check bar installation and bushings (already has energy bushings), will make more clearance in the stru tower to get more caster, then meter bump steer to check.

But I don't know where I might get a stiffer rear anti sway bar that could get fit cause I've already has the torque arm and panhard bar and after market chassis fitted bars like hotchkis or steeda extra won't fit (I assume), any ideas?

drudis · 07-09-2003, 04:01 PM

For some reason I still cannot see the photos.
Email them to me drudis@ford.com or something...

lito · 07-09-2003, 04:28 PM

Really Sorry drudis, I've modded the site that host the photos making them smaller and forgot to edit the message, now I can't edit it anymore so I'm posting new links here. Thanks.

http://dettagli.no-ip.com/turagua060...2694ModRez.htm

http://dettagli.no-ip.com/turagua060...s/DSCN2697.htm

http://dettagli.no-ip.com/turagua060...s/DSCN2731.htm

BTW I'm thinking on adding the adj anti sway bar MM sales http://www.maximummotorsports.com/rsb.asp the -4 one.

drudis · 07-09-2003, 06:32 PM

IMOHO, the springs and shocks are at about th right setting, especially th rears.
(Depending on who you ask) My front 425# coilovers are either 850# or 1700# (2x or 4x). And I still barely lift the front tire. That could be solved with 50# heavier rear spring, and I am only running 350# rears (soft).
See this link for a series of photos: http://www.dariusrudis.com/mustang/svtoa/

I would try playing with rear panhard height. IMOHO, its the roll center of he rear that is producing the front to roll over on itself.

06-30-2003, 11:48 AM	#1
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	Handling help Drudis Would you please take a look at these photos and tell me what you think on how the tires are put onto the ground. http://dettagli.no-ip.com/turagua060...2694ModRez.jpg http://dettagli.no-ip.com/turagua0603/DSCN2697.JPG http://dettagli.no-ip.com/turagua0603/DSCN2731.JPG The car is in it's almost stock weight, a fewer pound here and there but just a few. Front: It has relocated bushings on stock front A-arms, 950-1050lbs H&R springs, koni yellows, middle setting and stock anti sway bar (1 5/1" if I not wrong) Rear: MM Alum panhard, MM Torque Arm 390-430 lbs springs, cobra rear sway bar, koni yellows. I forgot, it has 1.8 camber and 3.5 caster, toe is in it's stocks toe out limits, w/steeda camber plates. I know it may need a little more camber on temp readings that we got on the pyrometer. I'm thinking on findind a better sway bars front/rear, what do you think? __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com Last edited by lito; 06-30-2003 at 07:36 PM..

06-30-2003, 03:41 PM	#2
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	It seems like your rear springs are a bit soft at 300 lb/in. If they are in the stock location, I would think that with the torque arm and the 1000 lb/in front springs that you would be getting understeer. Most folks recommend closer to 350 or 400 lb/in for that type of setup so that the rear will take on more cornering load. __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

06-30-2003, 05:23 PM	#3
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	I might remind the number wrong, the springs where recommended by Chuck of MM given my current front springs, I'll check that out again. __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com

06-30-2003, 07:37 PM	#4
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	I was wrong, 390-430 lbs __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com

07-01-2003, 03:09 PM	#5
blue00gt Mustang Addict Join Date: Jan 2001 Location: McKinney, TX Posts: 1,294	Cool, that sounds more like the right rear spring rate for your combo. If you can get more positive caster with the plates you have I would put it up to 5 deg. or so. This will turn into more negative camber as you turn the wheel without causing extra uneven tire wear going straight. __________________ Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s

07-01-2003, 04:50 PM	#6
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	I'll have to take some material from shock towers. I'll do that. Any other ideas? __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com

07-02-2003, 02:11 AM	#7
pearlgt40 306 Registered Member Join Date: May 2002 Location: Long Island, NY Posts: 14	do you have any other poly bushings? if so....then i would recommend an aftermarket anti-sway bar since it looks as though the car is rolling onto the outside wheel and lifting the inside. ...Energy Suspension Master Kit.. i have it. Works great. __________________ 306 Short Block, Forged Pistons, GT-40 Irons, Ford Racing 1.6 Ratio Rockers, GT-40 Upper and Lower Intake, B-303 Cam, 24 lb Injectors, 70 MM Throttle Body, 75 mm MAF, MAC Cold Air Intake(in fender), March Ram Air Scoop, MAC Longtubes, Offroad H-Pipe 2.5", No Cats, 40 Series Flows, 2.73's(eek...), Kenny Brown Subframes, World Class T-5, Pro 5-0 Tower Shifter

07-02-2003, 02:12 AM	#8
pearlgt40 306 Registered Member Join Date: May 2002 Location: Long Island, NY Posts: 14	beautiful fox by the way. __________________ 306 Short Block, Forged Pistons, GT-40 Irons, Ford Racing 1.6 Ratio Rockers, GT-40 Upper and Lower Intake, B-303 Cam, 24 lb Injectors, 70 MM Throttle Body, 75 mm MAF, MAC Cold Air Intake(in fender), March Ram Air Scoop, MAC Longtubes, Offroad H-Pipe 2.5", No Cats, 40 Series Flows, 2.73's(eek...), Kenny Brown Subframes, World Class T-5, Pro 5-0 Tower Shifter

07-04-2003, 05:26 PM	#9
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	I think I've found a 1 3/8" front bar, would check bar installation and bushings (already has energy bushings), will make more clearance in the stru tower to get more caster, then meter bump steer to check. But I don't know where I might get a stiffer rear anti sway bar that could get fit cause I've already has the torque arm and panhard bar and after market chassis fitted bars like hotchkis or steeda extra won't fit (I assume), any ideas? __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com

07-09-2003, 04:01 PM	#10
drudis Moderator Join Date: Dec 1999 Location: Livonia, MI, USA Posts: 1,194	For some reason I still cannot see the photos. Email them to me drudis@ford.com or something... __________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com

07-09-2003, 04:28 PM	#11
lito Registered Member Join Date: Feb 1999 Location: Caracas, Venezuela Posts: 81	Really Sorry drudis, I've modded the site that host the photos making them smaller and forgot to edit the message, now I can't edit it anymore so I'm posting new links here. Thanks. http://dettagli.no-ip.com/turagua060...2694ModRez.htm http://dettagli.no-ip.com/turagua060...s/DSCN2697.htm http://dettagli.no-ip.com/turagua060...s/DSCN2731.htm BTW I'm thinking on adding the adj anti sway bar MM sales http://www.maximummotorsports.com/rsb.asp the -4 one. __________________ 92GT, SOLO RACER, COBRA BRAKES, R1 TIRES, GT40, GT40X HEADS 58CC, 24LBS, 70MM/65MM, E303, MAC 1"5/8 LT HEADERS, 3" XPIPE AND EXHAUST W/CUT OFFS, 4.10, H&R 950-1050 SPRINGS, BILSTEIN SHOCKS, MM PANHARD AND TA, MANY ROAD RACE MODS, CORVETTE, CAMARO, RX7 AND SUPRA SOLO EVENT EATER www.killersracing.com www.clubcopa.com

07-09-2003, 06:32 PM	#12
drudis Moderator Join Date: Dec 1999 Location: Livonia, MI, USA Posts: 1,194	IMOHO, the springs and shocks are at about th right setting, especially th rears. (Depending on who you ask) My front 425# coilovers are either 850# or 1700# (2x or 4x). And I still barely lift the front tire. That could be solved with 50# heavier rear spring, and I am only running 350# rears (soft). See this link for a series of photos: http://www.dariusrudis.com/mustang/svtoa/ I would try playing with rear panhard height. IMOHO, its the roll center of he rear that is producing the front to roll over on itself. __________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Handling set-up	polara7777	Corner Carvers Delight	3	05-13-2002 11:49 AM
gas millage and handling question	Cataract2	Blue Oval Lounge	7	04-17-2002 10:02 PM
Best Handling Early Mustang?	bigcarguy	Classic Mustangs	6	12-29-2001 08:33 PM
Handling	Black02GT	Modular Madness	5	11-28-2001 02:46 AM
handling	yusuf	Classic Mustangs	8	06-12-2001 03:51 PM