Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
06-07-2001, 10:49 PM
|
#1 |
|
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
lower intake gaskets? will they work?
i went to car quest the other day to get lower intake gaskets and they didnt have fel pro so they gave me a car quest intake gasket set..has gasket for lower intake and stock upper..cork gaskets and a O ring gasket? all i need is the lower gasket but will these work ok?
------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Future Mods:3.73's,Pro 5.0,accufab 70mm tb,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's,four cylinder springs up front ICQ#35670781  |
|
|
|
06-08-2001, 12:35 PM
|
#2 |
|
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
ttt
------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Future Mods:3.73's,Pro 5.0,accufab 70mm tb,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's,four cylinder springs up front ICQ#35670781 |
|
|
|
|
06-08-2001, 01:46 PM
|
#3 |
|
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
Demon-if they cross reference with the Felpro make sure they match the 1250. The O-ring is for the distributor and DON'T USE THE CORK END PIECES, use a nice bead of silicone to seal that up.
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! |
|
|
|
|
06-08-2001, 06:40 PM
|
#4 |
|
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
the gaskets that the guy gave me was for stock replacement...so if the stock lower intake gasket is the same as a fel pro 1250 then it will work...is it????
------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Future Mods:3.73's,Pro 5.0,accufab 70mm tb,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's,four cylinder springs up front ICQ#35670781 |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Summer Plans | Stang_Girl617 | Blue Oval Lounge | 12 | 06-06-2004 02:22 AM |
| Head and intake flow. Something to think about. :) | 5ohCOUPE | Windsor Power | 3 | 03-16-2003 08:52 AM |
| TFS intake gaskets??? | DemonGT | Windsor Power | 2 | 05-22-2001 02:59 PM |
| HELP LOWER INTAKE MNIFOLD LEAK | red90lx | Windsor Power | 1 | 05-08-2001 09:49 AM |
| Head Gaskets, Header Gaskets, Intake Gaskets, etc | AxemanZZ | Windsor Power | 8 | 01-11-2001 01:09 PM |