![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 1999
Location: Overland Park, KS, USA
Posts: 1,631
|
![]() I'm not sure if this is the right place to post this, but I'm re-doing my front suspension and wanted some suggestions. I want a tubular K member and coil over springs. Now...this car will be a fair weather/weekend warrior car but I might also show it so this stuff has to ride as well as it works. This will also be dropped in along with a new motor, transmission, rear end, and a torque arm/panhard bar setup. Can anyone give me any suggestions?
------------------ 1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: May 1999
Location: Blacksburg, VA
Posts: 1,526
|
![]() Griggs is always good. Its not cheap, but you deffently get what you pay for.
http://www.griggsracing.com/ Maximum Motorsports is also coming out with a K-member at some point. They're another good quality company and a bit cheaper then Griggs. http://www.maximummotorsports.com/ |
![]() |
![]() |
![]() |
#3 |
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
![]() Call www.griggsracing.com and hide the VISA bill
![]() Take a look at my homepage. I just completed the front setup (need to post newer photos) but finally have the whole ehchalada... ------------------ Darius Rudis Roadracer: Home built t-arm/panhard suspension powered by an S-trimmed motor :-) My Mustang Page |
![]() |
![]() |
![]() |
#4 | |
Registered Member
Join Date: May 1999
Location: Blacksburg, VA
Posts: 1,526
|
![]() Quote:
![]() |
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Apr 1999
Location: Overland Park, KS, USA
Posts: 1,631
|
![]() Hey drudis-
That stuff looks pretty sweet. What parts exactly did you get from them? I've seen their website before a looooong time ago and the stuff wasn't insanely expensive (a little pricey, but didn't seem too bad). That looks like a bad @ss setup. ------------------ 1984 1/2 GT350 (#842 Hatchback w/ T-tops), 302HO, Comp cams Xtreme Energy cam, Carter 625cfm carb, Weiand Stealth intake, MSD distributor, MSD coil, FMS 9mm wires, 1 5/8" MAC unequal shorties, 2 1/2" MAC Prochamber H-pipe, Flowmaster 2 chambers, KYBs, 16"x8" 4 lug Cobra Rs, Falken 245/45ZR16s |
![]() |
![]() |
![]() |
#6 |
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
![]() I bought THIS
![]() See my homepage for LOTS more photos of the install. ------------------ Darius Rudis Roadracer: Home built t-arm/panhard suspension powered by an S-trimmed motor :-) My Mustang Page |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
front suspension upgrades | hobgoblin351 | Corner Carvers Delight | 1 | 03-31-2004 11:59 PM |
front suspension upgrades | hobgoblin351 | Classic Mustangs | 2 | 02-26-2004 12:34 PM |
Mustang suspension | Skankin | Corner Carvers Delight | 1 | 08-17-2001 05:10 PM |
Front suspension hop-up | 84_GT350 | Windsor Power | 0 | 05-30-2001 02:47 AM |
65 Front End Suspension. | red | Classic Mustangs | 3 | 04-04-1999 11:38 AM |