Spindle Identification

JohnnyG · 08-06-2002, 01:57 PM

Is there any way of positively identifying whether a spindle is an SN-95 or an SN-96 spindle?

I bought a used front-end braking set-up from MustangParts Specialties and they told me the spindles came from a 1995 car, but it already had loaded PBR calipers bolted to it, which leads me to believe it came from a 99+ V6 or GT. Also, I seem to have more clearance behind my Cobra R's than I would have expected... which makes me lean towards an SN-96 spindle. How can I tell?

-John

97snakedriver · 08-10-2002, 01:59 AM

Look at the arm for the tie-rod. The 96+'s have a straight arm while the 94-95's have a bent arm. The 96+ will also make for a +8mm track width per side. Here's a picture of the difference:

http://www.corner-carvers.com/forums...=&postid=28925

drudis · 08-13-2002, 11:26 PM

I have had both
1995:

and 1996 (my current setup):

08-06-2002, 01:57 PM	#1 (permalink)
JohnnyG Registered Member Join Date: Feb 1999 Location: Baltimore, MD USA Posts: 105	Spindle Identification Is there any way of positively identifying whether a spindle is an SN-95 or an SN-96 spindle? I bought a used front-end braking set-up from MustangParts Specialties and they told me the spindles came from a 1995 car, but it already had loaded PBR calipers bolted to it, which leads me to believe it came from a 99+ V6 or GT. Also, I seem to have more clearance behind my Cobra R's than I would have expected... which makes me lean towards an SN-96 spindle. How can I tell? -John __________________ 1991 GT Vert- Black/Black/Black Exhaust, Tremec, Tri-Ax, Centerforce Dual Friction, 3.73's, Rear Seat Delete MM Road & Track Kit PBR 5-Lug Brakes Cobra R's w/ 255 Rubber Rice Hater's Club #60

08-13-2002, 11:26 PM	#3 (permalink)
drudis Moderator Join Date: Dec 1999 Location: Livonia, MI, USA Posts: 1,194	I have had both 1995: and 1996 (my current setup): __________________ Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Adjustment nut on spindle - what ft/lbs?	302 LX Eric	Windsor Power	2	04-17-2003 10:49 PM
Spindle Identification	JohnnyG	Windsor Power	0	08-08-2002 11:00 AM
spindle mounted rims?	WADS56	Windsor Power	1	08-07-2002 07:53 AM
302 engine identification	ponydude	Classic Mustangs	9	07-17-2001 11:07 AM
Motorcraft/Holley carb Identification	agazzo	Windsor Power	1	03-31-2001 07:38 PM

08-10-2002, 01:59 AM	#2 (permalink)
97snakedriver Registered Member Join Date: Jun 1999 Location: Blacksburg, VA Posts: 1,526	Look at the arm for the tie-rod. The 96+'s have a straight arm while the 94-95's have a bent arm. The 96+ will also make for a +8mm track width per side. Here's a picture of the difference: http://www.corner-carvers.com/forums...=&postid=28925

Sponsored Links