© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
11-03-2001, 01:04 PM | #1 |
Registered Member
Join Date: Jun 2001
Location: butler pa
Posts: 303
|
do i need camber caster plates
hi i am putting together a total redo for my wheels and suspension and lowering springs are a part of this i am going to use the intrax springs from summit 2 inch drop will i need camber caster plates to align it properly the car will also have the sn95 spindle conversion done it is a 92 lx
thanks for your time ------------------ 92lx wannabe saleen bbk cold air h-pipe flowmasters the rest of the way complete saleen body kit and wing |
11-03-2001, 03:36 PM | #2 |
Registered Member
Join Date: May 1999
Posts: 5,246
|
Any time you lower the car caster/camber plates are a good idea. The stock units are just very lacking in adjustment.
|
11-03-2001, 05:10 PM | #3 |
Registered Member
Join Date: Dec 2000
Location: Waterloo, ON, Canada
Posts: 214
|
Yeah, I agree, BUT, if you're strapped for cash, I was told that you can do without the C/C plates until a later time, cause there is a bit of adjustment in the stock C/C plates. (for drops of around 1.5" front, the stock setup could be adjust properly!)
don't forget the bump-steer kit.. ------------------ 94 GT (triple black) FMS 17" Cobra R's / AL Driveshaft / 3.27's K&N, 190 lph, subframes, motorsports hd clutch, mac pulleys, msd coil MAC Shifter/Gauges/Pedals, Euro Clear Projectors & Corners My CAR! |
11-03-2001, 06:07 PM | #4 |
The Photoshop Guru
Join Date: Feb 2001
Location: Mecca, Indiana
Posts: 1,419
|
I'd recommend C/C plates for that much of a drop. I'm also curious about those springs. I've never seen anyone using them so I'd make sure you get some info on them before ordering if you haven't already.
------------------ Gunning for 12's! Buy your parts here ICQ# 42269241 |
11-03-2001, 09:47 PM | #5 |
Registered Member
Join Date: Jan 1999
Location: Clayton, North Carolina, USA
Posts: 803
|
With a 2" drop you will need CC plates. With the 1-1/2" drop I did to mine I also had to have the CC plates to get it properly aligned.
------------------ fordgasm CLICK HERE to see my 87 GT |
11-04-2001, 01:01 PM | #6 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
with that much of a drop you will definently need c/c plates.
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help woth installing groundpounder coilovers with BBK caster camber plates | ciara | Windsor Power | 0 | 01-10-2004 01:08 PM |
Caster camber plates ? | COUSIN ROB | Modular Madness | 6 | 04-30-2003 05:28 PM |
Always need caster camber plates? | squid | Windsor Power | 3 | 03-23-2003 11:52 PM |
caster camber plates | horsesnake95 | Windsor Power | 2 | 10-15-2002 11:50 AM |
Steeda vs MM Caster Camber Plates | Mustangbelle306 | Corner Carvers Delight | 4 | 02-25-2002 05:47 PM |