roller 460?

gofastmercury · 09-06-2002, 06:53 PM

When did ford make a roller 460? Never new that they did at all till I saw a few posts on here (questions questions....) I have 460 out of a 92 f350 in my garage I was going to uise as a core, it would be neet if had roller stuff in it. And if it did, does any opne make cams for this? looking for torque, not big rpm.

95GTS · 09-09-2002, 10:31 AM

Did you take off the upper/lower intakes to see if it is roller? That'd be one way to tell. You might check on www.fordtrucks.com/ and post a question over there to find out for sure.

gofastmercury · 09-10-2002, 11:14 PM

Just been too buzy(lazy) to take it apart. I'll check that site.

09-06-2002, 06:53 PM	#1
gofastmercury Registered Member Join Date: May 2001 Location: calgary alberta canada Posts: 366	roller 460? When did ford make a roller 460? Never new that they did at all till I saw a few posts on here (questions questions....) I have 460 out of a 92 f350 in my garage I was going to uise as a core, it would be neet if had roller stuff in it. And if it did, does any opne make cams for this? looking for torque, not big rpm. __________________ 93LXcopcarSOLD14.3@96 @ 4500ft 2.02 60ft on street tires. my 67 ranchero NOT A 390 ANY MORE! 460! 3.70's cast manifolds, comp cams 262H, performer, 750DP 100K out of 79 F250 NEW(oct20/02)14.58@95mph 2.3 60 ft corrects to:13.86@100 66 merc comet351w, isky roller 600 lift 268/260@.050, vic jr. 700DP, 5000stall, 4.56's c-4, 3400lbs with driver 12.3@110 @ 4000ft 1.69 60 ft corrects to:11.69@115

09-09-2002, 10:31 AM	#2
95GTS Git jiggy Join Date: Oct 1999 Location: MO USA Posts: 865	Did you take off the upper/lower intakes to see if it is roller? That'd be one way to tell. You might check on www.fordtrucks.com/ and post a question over there to find out for sure. __________________ 1967 Mustang Coupe

09-10-2002, 11:14 PM	#3
gofastmercury Registered Member Join Date: May 2001 Location: calgary alberta canada Posts: 366	Just been too buzy(lazy) to take it apart. I'll check that site. __________________ 93LXcopcarSOLD14.3@96 @ 4500ft 2.02 60ft on street tires. my 67 ranchero NOT A 390 ANY MORE! 460! 3.70's cast manifolds, comp cams 262H, performer, 750DP 100K out of 79 F250 NEW(oct20/02)14.58@95mph 2.3 60 ft corrects to:13.86@100 66 merc comet351w, isky roller 600 lift 268/260@.050, vic jr. 700DP, 5000stall, 4.56's c-4, 3400lbs with driver 12.3@110 @ 4000ft 1.69 60 ft corrects to:11.69@115

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
building a stroker need advice on solid roller or hydrallic roller cam ??	Mustangboy89	Windsor Power	4	06-06-2003 02:10 PM
Solid Roller ?	STROKER BILLY	Windsor Power	5	11-19-2002 12:04 AM
351W roller conversion	Capri306	Windsor Power	4	02-14-2002 04:49 PM
hydraulic roller valvetrain for HP street??	Stang_ROTY	Windsor Power	2	04-27-2001 01:09 AM
Non roller to roller 351 block ?????	88workcar	Windsor Power	2	03-04-2001 12:45 PM