T-body elbow adapter for SN95 question?????

cojonepony · 06-25-2001, 09:49 PM

I'm going to install heads/cam/intake soon and I've got a used GT-40 intake so I bought an Edelbrock elbow adapter for an SN95 car. The thing I'm curious about is the EGR valve. The adapter blocks off the small EGR opening under the main (2.75") opening on the GT-40 upper plenum. Does the EGR introduce hot exhaust air right into the main throttle opening on an SN95?

Patrick Boetticher · 06-27-2001, 11:13 AM

the opening that i think you are talking about is the little oval opening below the large tb opening... that opening goes through manifold down to the lower manifold. you it is blocked off byt he egr elbow. you do not need this cuz the heat riser tube that comes up from header and is intorduced through the elbow..... i had that same problem when i installed mine

------------------
ALL NEW PPG Torch Red 95GT, 304ci block, Forged pistons, Ported Explorer Intake, E-303 cam, fully ported and polished and milled E-7 heads, 75mm MAS, BBK Adj. fuel Reg & gauge, BBK Shorty Headers, BBK H-pipe, March Pulleys, 2 Chamber Flowmasters, Kenny Brown 6 point Roll cage, Kenny Brown Panhard Bar, Powerslot Rotors, PBR twin piston calipers, Eibach Sportline Springs, 180* Thermostat, 1/2 Plenum Spacer, MSD 6AL, MSD Master Blaster, MSD 8.8 Wires, 24# Racing Injectors, AFS 10.5" Cobra R's, Nit

06-25-2001, 09:49 PM	#1
cojonepony Registered Member Join Date: Feb 2000 Posts: 132	T-body elbow adapter for SN95 question????? I'm going to install heads/cam/intake soon and I've got a used GT-40 intake so I bought an Edelbrock elbow adapter for an SN95 car. The thing I'm curious about is the EGR valve. The adapter blocks off the small EGR opening under the main (2.75") opening on the GT-40 upper plenum. Does the EGR introduce hot exhaust air right into the main throttle opening on an SN95?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
75mm throttle body question	jinx6570	Modular Madness	3	11-12-2003 08:31 AM
Body Filler Question	ChunkFunky	Windsor Power	5	02-11-2003 07:34 AM
throttle body and egr question	scale	Windsor Power	6	04-02-2002 10:03 PM
throttle body question?	acidangel316	Windsor Power	0	08-28-2001 01:24 AM
Please help w/Throttle Body install question??	Ersel	Modular Madness	1	07-08-2000 06:04 PM

06-27-2001, 11:13 AM	#2
Patrick Boetticher Registered Member Join Date: Feb 1999 Location: Camarillo/Thousand Oaks Ca Posts: 223	the opening that i think you are talking about is the little oval opening below the large tb opening... that opening goes through manifold down to the lower manifold. you it is blocked off byt he egr elbow. you do not need this cuz the heat riser tube that comes up from header and is intorduced through the elbow..... i had that same problem when i installed mine ------------------ ALL NEW PPG Torch Red 95GT, 304ci block, Forged pistons, Ported Explorer Intake, E-303 cam, fully ported and polished and milled E-7 heads, 75mm MAS, BBK Adj. fuel Reg & gauge, BBK Shorty Headers, BBK H-pipe, March Pulleys, 2 Chamber Flowmasters, Kenny Brown 6 point Roll cage, Kenny Brown Panhard Bar, Powerslot Rotors, PBR twin piston calipers, Eibach Sportline Springs, 180* Thermostat, 1/2 Plenum Spacer, MSD 6AL, MSD Master Blaster, MSD 8.8 Wires, 24# Racing Injectors, AFS 10.5" Cobra R's, Nit