DEAD MACH

OLDFART · 05-09-2001, 05:31 AM

HAD Mach 460 system. DEAD. All speakers work but no AMPS. ANy clue where to get a wiring Diagram From? Or whta might be bad.
1. Fuses are good and No wires appear to be cut.
2. There was and ignition bleed thru to the speakers befroe it croaked.

------------------
Take Care

slo95 · 05-10-2001, 09:30 AM

Are you wanting to install aftermarket amps? There are two different wiring harnesses you can get that will allow you to do just that, kinda pricey. Seen them at circuit city and a car audio specialty shop. I never had luck with them, and ended up gutting the MACH system. The harness seem to use the high side and made the volume control crazy - but, it worked.

slo95 · 05-11-2001, 10:25 AM

I was picking up come cd's yesterday at Circuit city, and figured what the heck. I asked the tech installers about the Ford alarm, and they were able to get a spec sheet and print it out. it is a color code list of wires and what they do. this is for the keyless entry, so i think you should be able to get something for the mach system, if you ask nice?

PonySpirit · 05-17-2002, 03:23 PM

This is an old thread so hope you're getting responses in your mailbox. Did you make sure to use the harness that was plugged into the original receiver. Some professional installers do use that harness which hits the amps.

If you had the stereo professionally installed somewhere and they opted to use the other harness which comes standard on all Fords with and without 460 then it would bypass the amps. This harness is usually attached to the right wall when not in use ( i.e. in models with Mach 460 ).

Torinalth · 06-11-2002, 10:22 PM

also, said you checked the fuses, but did ya check the fuses on the amps them selves?

Torinalth

05-09-2001, 05:31 AM	#1
OLDFART Registered Member Join Date: May 2001 Location: Orange Park, Florida Posts: 2	DEAD MACH HAD Mach 460 system. DEAD. All speakers work but no AMPS. ANy clue where to get a wiring Diagram From? Or whta might be bad. 1. Fuses are good and No wires appear to be cut. 2. There was and ignition bleed thru to the speakers befroe it croaked. ------------------ Take Care

05-17-2002, 03:23 PM	#4
PonySpirit Registered Member Join Date: May 2002 Location: Boston, MA Posts: 2	mach 460 amp harness This is an old thread so hope you're getting responses in your mailbox. Did you make sure to use the harness that was plugged into the original receiver. Some professional installers do use that harness which hits the amps. If you had the stereo professionally installed somewhere and they opted to use the other harness which comes standard on all Fords with and without 460 then it would bypass the amps. This harness is usually attached to the right wall when not in use ( i.e. in models with Mach 460 ).

06-11-2002, 10:22 PM	#5
Torinalth Registered Member Join Date: May 2002 Location: Chapel Hill, NC - USA Posts: 188	also, said you checked the fuses, but did ya check the fuses on the amps them selves? Torinalth __________________ When you finally shut down the car, just sit back and remember the run.... win or lose, you know it was a surge of adreneline

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
04 Mach vs 03 Cobra	RBatson	Blue Oval Lounge	20	01-13-2004 09:07 PM
VIN question on 69 Mach 1	DRASTiK	Classic Mustangs	9	10-31-2002 06:06 PM
Cop dead. Family dead.	The Deuce	Blue Oval Lounge	5	09-25-2002 03:16 PM
Mach I vs 02 GT	dod racing	Modular Madness	15	07-11-2002 06:20 PM
SportsRoof or Mach 1??? HELP!	6T9PONY	Classic Mustangs	14	10-30-2001 12:36 AM

05-10-2001, 09:30 AM	#2
slo95 Registered Member Join Date: Dec 2000 Posts: 168	Are you wanting to install aftermarket amps? There are two different wiring harnesses you can get that will allow you to do just that, kinda pricey. Seen them at circuit city and a car audio specialty shop. I never had luck with them, and ended up gutting the MACH system. The harness seem to use the high side and made the volume control crazy - but, it worked.

05-11-2001, 10:25 AM	#3
slo95 Registered Member Join Date: Dec 2000 Posts: 168	I was picking up come cd's yesterday at Circuit city, and figured what the heck. I asked the tech installers about the Ford alarm, and they were able to get a spec sheet and print it out. it is a color code list of wires and what they do. this is for the keyless entry, so i think you should be able to get something for the mach system, if you ask nice?