![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 2002
Location: Portland Oregon
Posts: 247
|
![]() Is anyone out there running an Edelbrock RPM package on a 351 Windsor?
I would like to share some comments and double check some issues. My engine. .030 over 351 Windsor 1970 Block. Forged rods, Forged 9-1 pistons. inches (1262S Felpro Gasket) TFS/TW heads. Ported to 2 1/8 x 1 5/16 2.02 intake 1.6 exhaust RPM dual plane RPM Cam installed straight up 1.6 Roller Tip Rocker Arms Modified Holley 750 Carb 32 degrees max advance Crane Hi-6 and PS-71 Coil Shortie headers 2.5 inch dual exhausts with crossover Edelbrock RPM high flow mufflers C4 Automatic 3.25 Posi rear end. If you are running an edelbrock RPM package I would like to know what your ET's are with whatever gear and transmission you are using. What is your gas mileage? What is your running temperature? What is your overall impression of the package?
__________________
1966 Customized for daily street and highway domination. 358 Windsor running 425 HP C-4 Auto and 3.25 Posi |
![]() |
![]() |
![]() |
#2 |
The Redneck James Bond
Join Date: Sep 2000
Location: Fayetteville NC
Posts: 1,707
|
![]() Not sure of your cam specs, but I'm willing to guess that its a Low To Mid Range cam. With the C4 ratio's though, I'd go for a little Lower Rear Gear. Sounds like a sound package. Also, not knowing your cam specs, its hard to say if your carburated right or not.
__________________
64 1/2 "D" code Red Mustang Coupe. Red Baron, 2000 Perf Red Mustang GT. 5spd. Stage 2 CNC heads with Large Valves, Comp Cams (270-274 dur .550 lift), Forged Crank, DRP pistons, Manly H-beams, Pro M 87 mm Mass Air, 24lb Inj, 75mm TB, Plenum Spacer ,Long Tube Headers, Homemade H-pipe, 2 chamber Flows, 4:10's, Steeda Tri-Ax, LKW 70/30's, Eibach Drag Springs, Steeda SubFrames, Battle Boxes, Rear Girdle, Adj uppers, Alunimum Drshft, Southside Lift Bars. Project Cars, 64 1/2 6cyl coupe, 1930 Model A Nostalgia Rod. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 2002
Location: Portland Oregon
Posts: 247
|
![]() Cam specs are 224/234 duration at 0.050 lift. .496 lift on intake and .519 lift on exhaust.
Good vacume, runs with my 2000 rpm stall converter, and it is running HOT. I am going to have to try a radiator with offset inlets and outlets cause this old ford designed radiator just stinks. I am going to try to go with a wider radiator and cut my opening to match. I could pick up 20-25% more airflow that way. I would agree with you that this is a street and highway cam, but I would describe this as a street rod cam. Upper RPM power is substantial with the Trick Flow ported heads. CFM flow is 279 on the intake and 255 on the exhaust at the rated lift. This yields 425 hp at the flywheel and about 355 hp at the rear wheels at 6,500 RPM.
__________________
1966 Customized for daily street and highway domination. 358 Windsor running 425 HP C-4 Auto and 3.25 Posi |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Typhoon Intake vs Edelbrock Performer RPM | lucheski | Windsor Power | 1 | 07-13-2004 12:54 PM |
GM Engines | BLOCKER | Blue Oval Lounge | 2 | 04-13-2004 12:35 AM |
Speed Secret # 3 | jim_howard_pdx | Windsor Power | 13 | 11-09-2002 10:35 AM |
Experience with Edelbrock RPM Package | jim_howard_pdx | Windsor Power | 0 | 10-27-2002 01:10 AM |
flow numbers on edelbrock rpm intake? | Mach 1 | Windsor Power | 10 | 02-07-2002 09:20 AM |