MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Appearance & Detailing
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 01-18-2004, 02:00 AM   #1
mustardjohn
Registered Member
 
mustardjohn's Avatar
 
Join Date: Sep 2003
Location: Orange, TX
Posts: 360
Default Clay??!!

Lot of talk about clay.... Ok name some brands that are good. I want to go buy some and try it but what am I looking for??
__________________
2003 3.8 Mineral Gray, MAC CAI, K&N, Chin Spoiler
mustardjohn is offline   Reply With Quote
Old 01-18-2004, 02:51 PM   #2
mustardjohn
Registered Member
 
mustardjohn's Avatar
 
Join Date: Sep 2003
Location: Orange, TX
Posts: 360
Default

Here are a couple of brands I've found and a short article on "claying".

http://store.premiumautocare.net/pruseofdecl.html
__________________
2003 3.8 Mineral Gray, MAC CAI, K&N, Chin Spoiler
mustardjohn is offline   Reply With Quote
Old 01-19-2004, 02:18 PM   #3
xxxBlakexxx
Registered Member
 
xxxBlakexxx's Avatar
 
Join Date: Sep 2003
Location: Mountaintop, PA
Posts: 634
Post

John:

I have never yet used clay, but the research that I have done I would say that it's not the clay that matters so much as the motion and the lotion.



You are supposed to move the clay in a forwards and backwards motion...not circular. Also, some of the clay comes with detail spray that you use as the lubricant...for others you just get the bar and you make your own out of car wash soap.

I bought a clay bar about a week ago, but have not used yet as it isn't exactly car wash weather around here.

I really need to move.
__________________
"Children should not get cancer, but they do!" Help a child with cancer at www.homeoftheirown.org

My Stang:
2000 Mustang GT Vert - Steeda Tri-Ax Shifter; C&L Plenum; BBK 75 mm TB; Steeda Strut Tower Supports; Black "Deep Dish" Bullet Wheels; FRPP 4.10's; Steeda Subframes; SLP Catback & SLP Catted X-Pipe; SCT 4 Position Chip with 3 custom tunes; Steeda CAI; Venom-1000 Nitrous; Roush Stage 3 Body Kit; Bullet Suspension Package (on the way)
xxxBlakexxx is offline   Reply With Quote
Old 01-20-2004, 11:33 AM   #4
Stang_Crazy
It's never clean enough!
 
Stang_Crazy's Avatar
 
Join Date: Jan 1999
Location: Shaler, PA
Posts: 1,542
Default

It does matter which brand clay bar you go with....to an extent. Some cheap brands start to crumble after you use them, some brands aren't easy to bend and fold to expose a clean side, etc. Regardless of the brand, just make sure you use plenty of lubricant like Blake said and use back and forth motions, not circular. If the clay starts to 'stick' when you run it across the paint, you're not using enough lube.


I think the general consensus is the Zaino clay bar is one of the best.
__________________
~Dan
2001 SVT Lightning

89' GT : Taking up garage space and waiting for a buyer...

Rice Hater's Club - Member #11
Stang_Crazy is offline   Reply With Quote
Old 01-21-2004, 06:46 PM   #5
mustardjohn
Registered Member
 
mustardjohn's Avatar
 
Join Date: Sep 2003
Location: Orange, TX
Posts: 360
Default

Here is where you get Zaino clay. Looks cheaper than others but hard to tell the weight of the bar

http://www.zainostore.com/Merchant2/...duct_Code=Z-18
__________________
2003 3.8 Mineral Gray, MAC CAI, K&N, Chin Spoiler
mustardjohn is offline   Reply With Quote
Old 01-21-2004, 06:48 PM   #6
mustardjohn
Registered Member
 
mustardjohn's Avatar
 
Join Date: Sep 2003
Location: Orange, TX
Posts: 360
Default

Oh at WalMart you an get a 100g bar of Clay Magic with a spray bottle full of lubricant for $9.98. So it is probably cheaper.
__________________
2003 3.8 Mineral Gray, MAC CAI, K&N, Chin Spoiler
mustardjohn is offline   Reply With Quote
Old 01-22-2004, 07:47 PM   #7
Stang_Crazy
It's never clean enough!
 
Stang_Crazy's Avatar
 
Join Date: Jan 1999
Location: Shaler, PA
Posts: 1,542
Default

The weight of the bar doesn't really matter because you apply light to moderate pressure while moving it across the surface. Also, the size/weight isn't a huge factor because when both sides get dirty, you stretch and fold the bar to expose a new side.....so as the surface gets dirty, you just fold it over to get a clean side.

One bar (of any size/weight) SHOULD clay AT LEAST one whole car. In the Zaino jar, you get two bars. That is more than a year's supply. Remember, you only need to clay twice a year.
__________________
~Dan
2001 SVT Lightning

89' GT : Taking up garage space and waiting for a buyer...

Rice Hater's Club - Member #11
Stang_Crazy is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
clay aar0s Appearance & Detailing 7 05-22-2004 04:44 PM
Checking Valve Clearance OneBad91 Windsor Power 1 04-23-2004 10:43 PM
A Great Wax xxxBlakexxx Appearance & Detailing 32 01-26-2004 03:03 AM
Pistons for Larger Valves? MustangChile Classic Mustangs 4 02-28-2003 01:27 AM
Clay Magic Mr 5 0 Appearance & Detailing 5 05-28-2000 05:31 PM


All times are GMT -5. The time now is 06:06 PM.


SEARCH