MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Modular Madness
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 07-16-2002, 04:11 PM   #1
Doug McGinn
Registered Member
 
Join Date: May 2002
Location: Nebraska
Posts: 63
Default 2003 Cobra Parts

Does anyone have any links to parts for the 2003 Cobra?
Im looking for...
X-Pipe
Catbacks
Blower pulley
Cold Air Intake Kit
Doug McGinn is offline   Reply With Quote
Old 07-16-2002, 05:11 PM   #2
Hammer
AKA "Dr. Evil"
 
Hammer's Avatar
 
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
Default

The X-pipe and cat-backs SHOULD be the same as a 2001 Cobra.

As far as a Cold air induction, I don't think that there is a FORMAL package for it yet. Take a look at the article in 5.0 Mustang. It looks like they just fabricated an open element setup.

I've heard of folks using the blower pulley from a Lightning for a couple of extra pounds of boost....

That's all I've got right now.

Try contacting Mike Wilson at Dallas Mustang if you have further questions....
__________________
Uncle Sam
"What the hell is up with all the gauges?
Calling Captain Kirk, your ride awaits... Phasers on stun...."
Hammer is offline   Reply With Quote
Old 07-16-2002, 05:21 PM   #3
Doug McGinn
Registered Member
 
Join Date: May 2002
Location: Nebraska
Posts: 63
Default

Actually i think the engine was placed farther back in the engine compartment on the 2003 to improve handling,but i could be wrong.If thats the case then im not certain the 2001 exhaust parts will work.
As far as using an Open element backyard setup,the engine bay gets extremely warm.
The blower pully is another story,Im not going to swap out a pulley onto a brand new car without knowing what the actual boost pressure is going to be ect...
These parts are to expensive to order without knowing for a fact that they are going to work and what the end result is going to be.
Doug McGinn is offline   Reply With Quote
Old 07-16-2002, 05:58 PM   #4
Hammer
AKA "Dr. Evil"
 
Hammer's Avatar
 
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
Default

Hehe,
Welcome to owning a brand new "selective" car Doug.
Formal kits should be out pretty soon, but for now, the pickings will be slim. (and for the brave.)

As far as an open element setup, you could argue it a couple of ways....
1. An open element setup (Like a K&N Filtercharger) may get warmer air, but there is no bend in the tube nor restriction in the air flow before the MAF.
2. In the CAI's favor you have the cold (or less hot) air from the fenderwell...

As far as dyno #s, I've never seen a palpable difference in horsepower between the 2 types of setups. (Just an opinion from my experience...)

Like I said, I would contact Mike at Dallas Mustang if you have specific questions as they've already played with a few 03 Cobras.
(especially exhaust work...)
__________________
Uncle Sam
"What the hell is up with all the gauges?
Calling Captain Kirk, your ride awaits... Phasers on stun...."
Hammer is offline   Reply With Quote
Old 07-16-2002, 06:01 PM   #5
blue00gt
Mustang Addict
 
blue00gt's Avatar
 
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
Default

I've heard that the FRPP FR500 catback works on '03 Cobras and offers good gains.
__________________
Strike down the unroadworthy!
2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more
'94 Rio Red Cobra: All the bolt-ons, 3.73s
blue00gt is offline   Reply With Quote
Old 07-16-2002, 06:07 PM   #6
FireFinder20
I See Stupid People
 
FireFinder20's Avatar
 
Join Date: Mar 2002
Location: New Jersey
Posts: 47
Default

saw a pulley in action, it was the next size down, MM&FF was at ETown, NJ testing, but didn't give away a lot of info. I an tell you this, though, that sucker went 12.0@116 on the GoodYear F1 radials! it was more than likely 10 lbs, up from the stock 8...
FireFinder20 is offline   Reply With Quote
Old 07-16-2002, 06:23 PM   #7
Doug McGinn
Registered Member
 
Join Date: May 2002
Location: Nebraska
Posts: 63
Default

What would be the best Chip on the market today for this car?
As far as reliability, increased performance, and Cost.
My only Mods will be those listed above.
X-pipe
catbacks
Blower pulley (i want 10 or 11 pounds boost no more)
Cold air Intake.

Also has anyone heard anything about the knock sensors retarding the timing to much on the 32 Valve DOHC cobra engines?
Doug McGinn is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
2003 Cobra Transmission Silver Cobra Modular Madness 2 08-30-2002 11:39 PM
Raced a 02' Saleen, 01' cobra, and a freaky LS-1. Dark_5.0 Stang Stories 29 08-23-2002 07:12 PM
2003 SVT Cobra. Vision Blue Oval Lounge 2 02-19-2002 03:38 PM
The 2003 Mustang Cobra Nitrous Al Blue Oval Lounge 0 02-18-2002 06:30 PM
2001 Cobra Over Rated AGAIN!!!?!?!!! Wassup Ford? KillaZ350 Blue Oval Lounge 24 06-29-2001 05:24 PM


All times are GMT -5. The time now is 08:40 PM.


SEARCH