![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Mar 2003
Posts: 25
|
![]() i have an 89, vert with: a powerdyne supercharger(6psi) 70mm TB, 65mm mass air, 30lbs injectors, and adjustable fuel pressre regulator,headers, and an x pipe.
my question is are my injectors too big? will it damage anything if i run big injectors and turn down the fuel pressure to compensate? how much fuel pressure should i run? how much timming? what kind of spark plugs, how much gap spacing for the spark plugs? thanks any advice would be great!! |
![]() |
![]() |
![]() |
#2 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() you gotta list a little more than that. Stock H/C/I I assume? Are you using an FMU? To answer your question though, I don't think 30's are too big. The best way to know though would be to put it on a dyno and check the air/fuel ratio on there, or just buy an aftermarket wideband O2 sensor.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
|
![]() 30's are just right IMO.
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Mar 2003
Posts: 25
|
![]() hey,
yes i am using an fmu, the one that comes with the powerdyne kits, if that helps any. if you mean stock computer by saying Stock H/C/I I, than yes. Now that i have upgraded to 30lbs injectors will i have to change the chip in the fmu? can you run an supercharger without an fmu? im am kind of a newbie at this so please bare with me. I hope that helps |
![]() |
![]() |
![]() |
#5 | |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
![]() Quote:
Also, ignition is highly recommended, MSD Boost retard is a must, it helps with timing per lb of boost. More boost equals more timing, if there is no curve and/or coordination between the two you will blow a head gasket very quick. Good luck.
__________________
![]() |
|
![]() |
![]() |
![]() |
#6 | |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() Quote:
He'll need some real good luck if he follows that advice! ![]() You need to RETARD timing (less) with boost. An MSD 6 BTM would be a wise investment.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
|
![]() |
![]() |
![]() |
#7 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() H/C/I is just a short way of saying heads/cam/intake. I was just wondering if these parts were aftermarket or not.
Yes you can run a supercharger without an FMU, as that is the preferred way, as long as you have enough injector, and fuel pump. How big is your pump? 30's will give plenty of fuel without an FMU on an otherwise stock engine with only 6psi boost. I don't think I'd try it with the stock fuel pump though, I'd put in a 190 or 255lph to give you room to expand. Check out the forums at www.superchargerhelp.com sometime, there's a ton of good blower info over there.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Mar 2003
Posts: 25
|
![]() Sweet, its good to here that you can run the supercharger without the fmu, otherwise i would have to buy the chip from powerdyne. i also have an 9lbs pully that im goign to put on in a couple weeks, do u still theink i can run without an fmu? why is it preferred to run without an fmu?
yes the h/c/i are all stock, and i have upgraded the fuel pump to an 255lph. is there any other changes that you would suggest to make everything run well? perhaps an ignition box? i only wish i could afford an aftermarket h/i/c but i am only a student so money is a factor. |
![]() |
![]() |
![]() |
#9 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() You could pick up a used MSD-6AL pretty cheap. I know what you mean about the student thing, I came from the same boat, and have been slowly upgrading my college-budget bought parts.
The FMU is a way to cheat your fuel system into providing the extra fuel needed with boost. Although it can work fine in a lot of applications, it just isn't the most efficient way to do it. Having correctly sized injectors is the key to a properly running blower car.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
![]() huh? That's exactly what I said. more boost equals more timing, so he'll have to get the BTM to retard the timing per lb of boost or else the head gasket will blow quick...
__________________
![]() |
![]() |
![]() |
![]() |
#11 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() oh, sorry. The way I read more boost equals more timing was that the more boost you have, the more timing you have to put in it.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Leaky Injectors | Scrapla | Windsor Power | 3 | 03-10-2005 02:18 PM |
Advice on injectors...PKRWUD I'd like your advice on this one as well | silver_pilate | Windsor Power | 3 | 06-09-2003 08:59 AM |
differences in injectors? | '89GTStang | Windsor Power | 9 | 06-06-2003 02:39 AM |
MAF and FPR independent from injectors? | Nixon1 | Windsor Power | 4 | 03-01-2003 02:00 AM |
will Chevy injectors work in a Ford | tireburner163 | Windsor Power | 4 | 06-16-2001 07:16 PM |