Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
05-13-2003, 12:45 AM
|
#1 |
|
Registered Member
Join Date: Jan 2002
Location: Mt. Prospect,IL
Posts: 474
|
Gt40x heads gasket?
Well i found another problem... the darn intake gasket, the ports are to big for the darn gasket. I sucked another one in.. What gasket are these heads??? I am sick of replacing these things
later
__________________
87-ford-mustang-SOLD! mods: 3:73's, off road h-pipe, b303 cam in gt- 40 motor w/ Power Plus intake, edelbrock 70mm tb & egr spacer, 72mm C&L, bbk long tubes, tremec tranny, centerforce dual friction clutch, upr and lwr CA's 255lph FP and soon more to come.... when i have money again SOME ADVICE Don't do burn outs in reverse it is very expensive New times with dead hook on dr's 13.27@103 with 2.0 60 foots w/100lb system Fastest time to date: 12.8@113 |
|
|
|
05-14-2003, 12:12 AM
|
#2 |
|
Registered Member
Join Date: Jan 2001
Location: Moline Il
Posts: 901
|
What gaskets are you using? I use a Fel-pro 1262.
Andy
__________________
88 coupe 91 LX NMRA Pure Street 5120 |
|
|
|
|
05-14-2003, 01:15 AM
|
#3 |
|
Registered Member
Join Date: Jan 2002
Location: Mt. Prospect,IL
Posts: 474
|
smack me for this one stock
__________________
87-ford-mustang-SOLD! mods: 3:73's, off road h-pipe, b303 cam in gt- 40 motor w/ Power Plus intake, edelbrock 70mm tb & egr spacer, 72mm C&L, bbk long tubes, tremec tranny, centerforce dual friction clutch, upr and lwr CA's 255lph FP and soon more to come.... when i have money again SOME ADVICE Don't do burn outs in reverse it is very expensive New times with dead hook on dr's 13.27@103 with 2.0 60 foots w/100lb system Fastest time to date: 12.8@113 |
|
|
|
|
05-14-2003, 09:23 AM
|
#4 |
|
Sniffed too much n20
Join Date: Oct 1998
Location: Ont, Canada
Posts: 1,018
|
I think Felpro 1250 is the proper one. Its used for Edelbrock's, TFS (I think) and several others.
__________________
2002 Windsor Weekend Q16 Qualifier |
|
|
|
|
05-14-2003, 10:29 AM
|
#5 |
|
Registered Member
Join Date: Jan 2001
Location: Moline Il
Posts: 901
|
The 1250 has a port size of 1.20" x 2.00". The 1262 has a port size of 1.28" x 2.10". They are both .060 thick.
There is also a 1262R whose dimensions are 1.40 x 2.25. That one is .090 thick. Andy
__________________
88 coupe 91 LX NMRA Pure Street 5120 |
|
|
|
|
05-14-2003, 01:22 PM
|
#6 |
|
Registered Member
Join Date: Jan 2002
Location: Mt. Prospect,IL
Posts: 474
|
So which one would u say it it is 1250, 1262 or 1262r then??? hmmmm... if i pull off the intake then i have no car to drive to the part store
__________________
87-ford-mustang-SOLD! mods: 3:73's, off road h-pipe, b303 cam in gt- 40 motor w/ Power Plus intake, edelbrock 70mm tb & egr spacer, 72mm C&L, bbk long tubes, tremec tranny, centerforce dual friction clutch, upr and lwr CA's 255lph FP and soon more to come.... when i have money again SOME ADVICE Don't do burn outs in reverse it is very expensive New times with dead hook on dr's 13.27@103 with 2.0 60 foots w/100lb system Fastest time to date: 12.8@113 |
|
|
|
|
05-14-2003, 06:52 PM
|
#7 |
|
Registered Member
Join Date: Jan 2001
Location: Moline Il
Posts: 901
|
I use the 1262's currently with my TFS heads. I also used them when I had the GT40x's.
Andy
__________________
88 coupe 91 LX NMRA Pure Street 5120 |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Mounting cylinder heads without a gasket? | crazypete | Windsor Power | 18 | 07-15-2004 05:54 AM |
| 71 2v Cleveland heads on a mild 302 | crazypete | Windsor Power | 3 | 06-18-2004 07:05 PM |
| ??? about 351W heads on a 302 | vande97 | Windsor Power | 2 | 05-15-2002 10:42 AM |
| What kind of Windsor heads? | vetteeatr | Windsor Power | 11 | 10-28-2001 03:43 AM |
| For whoever it was considering using stock ported heads | 2FastLX | Windsor Power | 5 | 10-11-2001 01:53 PM |