© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-13-2006, 05:27 PM | #1 |
Registered Member
Join Date: Nov 2005
Location: Grantville, Pa
Posts: 29
|
How Much Horsepower Will I See At The Wheels?
I don't expect anybody to know exaclty how much horsepower power i'm making, but i would like some rough estimates on how much hp/tq i can expect at the rear wheels?
1992 Mustang 5.0 LX The mods: BBK CAI BBK Pullies Explorer Intake Manifold BBK 70mm Throttle Body/EGR Plate C&L 76mm MAF Sensor BBK 1 5/8" Longtubes BBK O/R H-PIpe Flowmaster Exhaust MSD 6AL Ignition #24lbs Injectors 255lph Fuel Pump NOS 175 Dry Shot Autolite 23's Gapped At 0.035 10* Base Timing 110 VP Race Fuel I didn't use the combo yet, but what is the max nitrous shot i can use before i blow head gaskets? Can my engine handle more hp than this? |
05-23-2006, 12:38 PM | #2 |
Registered Member
Join Date: May 2006
Posts: 10
|
Re: How Much Horsepower Will I See At The Wheels?
get better (hi performance) head gaskets
|
05-28-2006, 08:59 AM | #3 |
Undescribable
Join Date: Sep 1998
Location: Ft Myers Fla
Posts: 1,539
|
Re: How Much Horsepower Will I See At The Wheels?
you could blow head gasket with a low shot if your tune is wrong. why you using 110 vp race fuel?? it has lead in it. not good for your O2 sensors.
__________________
Rice Haters Club Member #101 |
05-28-2006, 02:46 PM | #4 |
Registered Member
Join Date: May 2006
Posts: 1
|
Re: How Much Horsepower Will I See At The Wheels?
Before you take it out and stomp on it, you need to go to your local shop with a dyno. Hopefully they can program your chip for you as well. That way you do not have to go back and forth from shop to shop. This can take some time. You have to see where you are at know with HP, then tune your chip to maximize performance, then dyno again to check what the changes to your chip did for HP and torque.
This is the only way to make sure that your engine is properly tuned for nitrous. |
06-30-2006, 05:19 PM | #5 |
Registered Member
Join Date: Jun 2006
Location: arlington tx
Posts: 2
|
Re: How Much Horsepower Will I See At The Wheels?
I say prolly 230 to 245 at the wheels with no juice. your motor can take a 150 shot assuming everything is in good working order. from personal experience, you need to retard your timing about 1 to 1 1/2 degrees for every extra 50 you have over a 50 shot. ie with a 150 timing should be around 7 degrees. bump the fuel pressure up a little too. use the vp only at the track when using the juice. on the street with your setup, its only a waste
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
raced a Supra Twin Turbo | Stang35th | Stang Stories | 63 | 08-23-2003 12:36 AM |
Weld Racing Wheels/ Street Wheels | jmjett01 | Modular Madness | 0 | 03-07-2003 11:45 AM |
Please Comment of Speed Secret # 2 | jim_howard_pdx | Windsor Power | 20 | 11-06-2002 11:44 AM |
15" Wheels on GT? | 2000GT-5spd | Modular Madness | 4 | 08-22-2002 12:08 PM |
349 horsepower at the wheels!!! | clearwaterms | Windsor Power | 5 | 05-29-2001 10:40 AM |