MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Power Adders
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 03-25-2004, 07:06 AM   #1
03stangGT
Registered Member
 
Join Date: Jun 2003
Location: Massachusettes
Posts: 26
Default build a cobra engine for boost set up??

I'm considering buying and engine to play with... here is the idea. My buddy who does the work on my car (as well as his 11 sec cobra) has a friend with a 1996 cobra motor he is selling. he can get me the complete motor for $1k the motor has 70k miles and runs mint! Would it be a waste of time for me to pick up that motor, install manley forged rods/pistons, and bearing kit, with low comp pistons? I'd like to build the motor for a blower or turbo application. This would all be going in a 2003 GT. I would like to keep my GT motor stock and keep it as a back up. I wanted to build a 4v because of a few things... I like a motor that rev's! and the cobra motor does compaired to my GT. Also it seems as though you get more HP from boost as compaired to a GT. Soo would this be a total waste of my time? Is there a better way to do this? keep in mind I'm not going to touch my GT motor, and I want to build a 4v, and not spend $5k. ANY opinions would be great....thanks in advance!

ps...the stock crank in the cobras are forged arent they? wouldnt wanna have to spend another $1k on that
03stangGT is offline   Reply With Quote
Old 03-31-2004, 12:52 AM   #2
RPM427
Registered Member
 
RPM427's Avatar
 
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
Default

That sounds like a good deal. How much power do you plan on making? That will determine if internal mods are needed.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway


-1994 Ranger w/ 427cid windsor (daily beater)
check it out!
RPM427 is offline   Reply With Quote
Old 03-31-2004, 10:33 AM   #3
Ackbar00
Rebel Fleet Commander
 
Ackbar00's Avatar
 
Join Date: Oct 2001
Location: Huber Heights, OH
Posts: 1,003
Default

Sounds expensive, but worthwile
__________________
1993 Mustang GT, PTK w/ T-64 - My Cardomain Webpage

11.25@123.5 on only 8 psi.
10.84@121 on only 1 headgasket



"The Truth is, Your the Weak, and I am the Tyranny of Evil Men!"

Ackbar00 is offline   Reply With Quote
Old 03-31-2004, 03:44 PM   #4
03stangGT
Registered Member
 
Join Date: Jun 2003
Location: Massachusettes
Posts: 26
Default

Well as far as power, my wish has alllwaayyyss been to have a turbo set up. but if I get impatient in my saving efforts I will most likely go with a novi s/c. because it is about 2k cheaper! and I would still be happy with that! I would like to be atleasttttt close if not a little more than 400hp to the wheels, because I would like to keep is as driveable as possible. The whole idea of me installing the forged rods/pistons, and having the block bored slightly is to start over with a fresh engine (or close to it). and also SHOULD be totally reliable that way. because I love this car and want to be able to drive it as often as I choose. I've got a question though...if this does not come with all the wireing from the cobra, where could I get all that? how much would it run me? thanks guys...also can you see any problems I may encounter?
03stangGT is offline   Reply With Quote
Old 03-31-2004, 06:11 PM   #5
RPM427
Registered Member
 
RPM427's Avatar
 
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
Default

You can pick up the wiring harness on ebay fairly cheap. I will be using a TEC3 engine managment system from Elecrotmotive for my 4v. It replaces all the factroy electrinics and allows you to run a supercharger without an FMU or a burned chip and will increase drivablilty and overall performance. Its only a few hundred more then a stock EEC and wiring with a burned chip and dyno tuning.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway


-1994 Ranger w/ 427cid windsor (daily beater)
check it out!
RPM427 is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
New Engine Build Help Young_Pony Windsor Power 2 08-22-2002 01:27 PM
build me an engine! BLOCKER Windsor Power 5 09-17-2001 10:36 PM
Is the 4.6 Cobra engine found in any other Ford Product Joel F Small Ponies 1 08-10-2001 04:58 PM
2001 Cobra Over Rated AGAIN!!!?!?!!! Wassup Ford? KillaZ350 Blue Oval Lounge 24 06-29-2001 05:24 PM


All times are GMT -5. The time now is 04:47 AM.


SEARCH