MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Power Adders
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 03-26-2009, 10:16 PM   #1
bailey_57
Registered Member
 
bailey_57's Avatar
 
Join Date: Mar 2000
Location: Berwick,Pa
Posts: 127
Default buying an older paxton blower fri?

I'm considering purchasing a blower from a guy for 700 dollars. He didn't give me the model number or the mileage. All he could tell me is it made 5 pounds when he had it installed and that its one of the older ball bearing paxtons. I don't know what to look for or even if thats a good price. The kit is complete, so what do you guys think. i'll post a pic of the head unit. as far as inspection what should i look for. obviously i need to spin the pulley but how tight or loose should it be? what noises are normal what are not?
__________________
'89 GT hatch back
performer rpm intake, performer rpm cylinder heads, fms e-303 cam, kirban adj fp regulator, holley 65mm tb, harland sharp 1.6 roller rockers, alum driveshaft, 3.73 gears (283 rwhp, 303 rwtq new numbers with new heads)
bailey_57 is offline   Reply With Quote
Old 03-26-2009, 10:20 PM   #2
bailey_57
Registered Member
 
bailey_57's Avatar
 
Join Date: Mar 2000
Location: Berwick,Pa
Posts: 127
Default Re: buying an older paxton blower fri?

blowerheadunit.jpeg
here it is guys what do you think?
__________________
'89 GT hatch back
performer rpm intake, performer rpm cylinder heads, fms e-303 cam, kirban adj fp regulator, holley 65mm tb, harland sharp 1.6 roller rockers, alum driveshaft, 3.73 gears (283 rwhp, 303 rwtq new numbers with new heads)
bailey_57 is offline   Reply With Quote
Old 03-26-2009, 11:00 PM   #3
StangFlyer
Founder
 
StangFlyer's Avatar
 
Join Date: Jun 1995
Location: Michigan
Posts: 19,326
Default Re: buying an older paxton blower fri?

Personally, I wouldn't do it. I would at least go with a NOVI 1200/1500/2000, Vortech, or a ProCharger unit at this point. I'd even get a nitrous system over an old ball drive Paxton. It looks like its seen some heavy, extended use from the photo too. I am not sure what your cash situation looks like, but if you can't immediately up the anti to one of the above I'd stick the $700 aside and keep adding to it until you can swing a new or even a used, more modern style system.

Any ways, I am commenting on this as someone who ran a ball drive Paxton for several years on a 302, and then went to a NOVI 2000 that I still have today on a 377 stroker in my 91 GT. I've also run various Nitrous systems back in the day.
__________________
StangFlyer
1991 Mustang GT - Supercharged 377 Stroker
2000 Ford Lightning - Project Lightning Hauler
Media Center Gallery - View my member photos
StangFlyer is offline   Reply With Quote
Old 03-28-2009, 07:13 PM   #4
bailey_57
Registered Member
 
bailey_57's Avatar
 
Join Date: Mar 2000
Location: Berwick,Pa
Posts: 127
Default Re: buying an older paxton blower fri?

impulse won! i bought it so i'll let you guys know how i make out. from the serial number i am assuming it is a sn92 model. everything is there for installation. i already have a 76mm c&l mass air meter and 30 lb injectors. do i need to use the fmu with this? also do i need to change my spark plugs. what are some good boost guages to run? thanks guys you always have good advice.
__________________
'89 GT hatch back
performer rpm intake, performer rpm cylinder heads, fms e-303 cam, kirban adj fp regulator, holley 65mm tb, harland sharp 1.6 roller rockers, alum driveshaft, 3.73 gears (283 rwhp, 303 rwtq new numbers with new heads)
bailey_57 is offline   Reply With Quote
Old 04-01-2009, 07:54 PM   #5
StangFlyer
Founder
 
StangFlyer's Avatar
 
Join Date: Jun 1995
Location: Michigan
Posts: 19,326
Default Re: buying an older paxton blower fri?

Whelp, guess that's that then!

What I would do is not run an FMU, but use the 30 lb injects with a boost sensitive fuel regulator and have your car chip tuned on a chassis dyno by an experienced EEC / Mustang tuner (i.e. burn a chip). This way you'll deliver the appropriate fuel ratio controlled by your computer.

I think I have an autometer boost guage.
__________________
StangFlyer
1991 Mustang GT - Supercharged 377 Stroker
2000 Ford Lightning - Project Lightning Hauler
Media Center Gallery - View my member photos
StangFlyer is offline   Reply With Quote
Old 04-29-2009, 03:24 PM   #6
bailey_57
Registered Member
 
bailey_57's Avatar
 
Join Date: Mar 2000
Location: Berwick,Pa
Posts: 127
Default Re: buying an older paxton blower fri?

well i bought the blower and figured out how it bolts up for the most part. i want to change the fluid before i use it. Does anyone know how much the SN92 takes. is a kirban adj fpr boost sensitive? thanks.
__________________
'89 GT hatch back
performer rpm intake, performer rpm cylinder heads, fms e-303 cam, kirban adj fp regulator, holley 65mm tb, harland sharp 1.6 roller rockers, alum driveshaft, 3.73 gears (283 rwhp, 303 rwtq new numbers with new heads)
bailey_57 is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Older model Paxton mrclean27_72 Power Adders 3 05-17-2005 03:52 AM
older GT to V6 LCAs, possible? Alpha Corner Carvers Delight 2 04-08-2005 11:49 PM
Newer Car/older Motor DANNER Windsor Power 0 03-26-2003 04:33 PM
Oil return line on blower? (Vortech or Paxton only) buddha Windsor Power 2 03-12-2001 07:58 PM
Roller cam for older motors??? rwhite65 Classic Mustangs 1 04-12-1999 11:04 PM


All times are GMT -5. The time now is 07:15 AM.


SEARCH