Heads & Inatke swap

St_Brawler · 05-16-2000, 02:03 PM

Is it possible to swap out the heads and intake from a 2000 GT and put them on a '97 GT?? And not do anything to the computer or does it have to be recalibrated ???

------------------
'97 GT, full lenght MAC headers, MAC Pro chamber h-pipe, Mac 2.5" Cat-back w/chrome tips, AODE, K&N, Eibach springs and a 150 NOS wet shot system.

Hammer · 05-16-2000, 02:27 PM

I know it's possible, but I don't know the ins and outs, or the costs involved. There are many threads referring to this subject over at the corral. www.corral.net

Hope this helps...

------------------
98 GT
Bassani X-pipe, Dyno-Max Cat backs, 3.73 gears, Steeda shifter, FMS pullies, 87mm MAF, Roush cold air kit, Eibach springs, and Zex 75 shot

97snakedriver · 05-16-2000, 02:28 PM

The '00 intake and heads flow much better (40 hp worth) then the '97, so yes you would have to at least recalibrate the computer.

According to my FRPP catalog the High Performance Engine Management Computer is "Recommended for only for use with M-6049-D46 cylinder heads"

The M-6049-D46 is the higher performance FRPP head.

05-16-2000, 02:03 PM	#1
St_Brawler Registered Member Join Date: Jan 2000 Location: Phoenix, Az Posts: 77	Heads & Inatke swap Is it possible to swap out the heads and intake from a 2000 GT and put them on a '97 GT?? And not do anything to the computer or does it have to be recalibrated ??? ------------------ '97 GT, full lenght MAC headers, MAC Pro chamber h-pipe, Mac 2.5" Cat-back w/chrome tips, AODE, K&N, Eibach springs and a 150 NOS wet shot system.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Whats the difference in GT40 and GT40P Heads?	RoushRacing6N17	Windsor Power	2	11-17-2003 11:52 PM
Price estimate for barely used Edel. Perf. RPM alum. heads w/ 2.02/1.60 valves??	Simi Stang	Windsor Power	13	11-03-2003 11:23 PM
??? about 351W heads on a 302	vande97	Windsor Power	2	05-15-2002 10:42 AM
For whoever it was considering using stock ported heads	2FastLX	Windsor Power	5	10-11-2001 01:53 PM
gotta know dart senior heads or edlebrock aluminum for a 347 to 351 swap	redrider	Windsor Power	3	05-07-2001 10:39 PM

05-16-2000, 02:27 PM	#2
Hammer AKA "Dr. Evil" Join Date: Feb 1999 Location: South Fork Ranch Posts: 1,721	I know it's possible, but I don't know the ins and outs, or the costs involved. There are many threads referring to this subject over at the corral. www.corral.net Hope this helps... ------------------ 98 GT Bassani X-pipe, Dyno-Max Cat backs, 3.73 gears, Steeda shifter, FMS pullies, 87mm MAF, Roush cold air kit, Eibach springs, and Zex 75 shot

05-16-2000, 02:28 PM	#3
97snakedriver Registered Member Join Date: May 1999 Location: Blacksburg, VA Posts: 1,526	The '00 intake and heads flow much better (40 hp worth) then the '97, so yes you would have to at least recalibrate the computer. According to my FRPP catalog the High Performance Engine Management Computer is "Recommended for only for use with M-6049-D46 cylinder heads" The M-6049-D46 is the higher performance FRPP head.