MustangWorks.com - The Ford Mustang Power Source!

Go Back   The Mustang Message Board > Mustang & Ford Tech > Windsor Power > 86 - 93 Mustang Tech
Register FAQ Members List Calendar Mark Forums Read

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
Old 05-24-2009, 03:33 PM   #1 (permalink)
buckneked7719
Registered Member
 
Join Date: Nov 2008
Posts: 7
Default Need Help Badly

i am having problems with my 92 mustang .it runs good for awhile then it will start to run rough while sitting at stop lights and will sometimes stall .when it does this the idle kinda surges up and down until it dies.when it starts to do this it also will not accelerate properly.it will not take wide open throttle it bogs and wont tach past 4 grand . if you turn it off wait a minute and restart it .its fine and then will eventualy do it again i have taken it to 3 different shops and gotten nowhere.i have replaced the plugs,wires,cap,rotor,ignition module.fuel filter,coil,egr valve,gas cap,checked the timing.replaced the computer with a reman.the check engine light is not on.it is throwing codes 44(AIR MANAGEMENT SYSTEM INOPERATIVE) and code94(SECONDARY AIR SYSTEM INOPERATIVE)one shop said the mass air flow sensor could be going bad.another said the fuel pressure regulator might be going.the throttle position sensor is within specs.ANY HELP WOULD BE APPRECIATED I DONT KNOW WHERE TO GO FROM HERE THANKS
buckneked7719 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 07-24-2009, 07:42 PM   #2 (permalink)
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 408
Default Re: Need Help Badly

go to a part store and get some maf cleaner and try to clean the maf.u can use brake cleaner but it takes the wax of if u dont do it right.if that fixes it make sure to get a new airfiter or if its a k&n make sure u clean it right
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.7 1.61 60ft tons of problems to fix and more money to spend!ahhhhhhh
1992 mustang gt
2000 chevy impala
1994 heavy chevy 4x4
78 century boat
92 skidoo
goodyear1984 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 11-02-2009, 09:39 PM   #3 (permalink)
fool4speed
Registered Member
 
Join Date: Oct 2009
Posts: 2
Default Re: Need Help Badly

Your IAC could be bad. Idle Air Control valve on the side of the throttle body...
fool4speed is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 11-04-2009, 12:23 AM   #4 (permalink)
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 408
Default Re: Need Help Badly

cannot be a iac that only control idle
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.7 1.61 60ft tons of problems to fix and more money to spend!ahhhhhhh
1992 mustang gt
2000 chevy impala
1994 heavy chevy 4x4
78 century boat
92 skidoo
goodyear1984 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 11-04-2009, 12:24 AM   #5 (permalink)
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 408
Default Re: Need Help Badly

what did u set the tps to?whats it at at wot
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.7 1.61 60ft tons of problems to fix and more money to spend!ahhhhhhh
1992 mustang gt
2000 chevy impala
1994 heavy chevy 4x4
78 century boat
92 skidoo
goodyear1984 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 11-04-2009, 08:32 PM   #6 (permalink)
fool4speed
Registered Member
 
Join Date: Oct 2009
Posts: 2
Cool Re: Need Help Badly

It measure's out the idle speed by how much air is flowing(fuel and air). If its stalling out on ya that could be it, but of course I know nothing...Your MAF sensor could be the culpret as well seein how its just up stream from your IAC...
fool4speed is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



Similar Threads
Thread Thread Starter Forum Replies Last Post
Not really Electronics, but help needed badly mcfuddlenuts Audio, Security, & Electronics 0 08-17-2007 11:14 PM
need carb help badly HP400RW Classic Mustangs 10 04-14-2003 03:10 AM
Advice needed badly...... MattwantsSpeed Windsor Power 2 07-16-2002 02:26 AM
I need you guys now badly on this one !! jetuomi Windsor Power 1 03-27-2002 12:49 AM
Need help badly!! 95GTS Windsor Power 6 02-02-2001 04:57 PM


All times are GMT -5. The time now is 04:09 PM.


SEARCH