© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-19-2001, 03:42 PM | #21 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Damn rick I didnt know you hit 11's, thats awesome!
Do you still have the stock rear and trans? Skyler
__________________
2001 BMW M3 6spd 12.79@108 RIP ---- 1993 Notch w/ 98 4V 4.6 Fasttt... -1989 Saleen Mustang #406- 12.32@109 -1999 Black Cobra Coupe- JBA Shorties, Bassani Cat-X, Magnaflow 3", Pulleys, 85mm Pro-M, Ported Intake, Soild Rear w/ 4.30s, Tubular Front End, X2C arms, 13lb batt, few others. |
12-19-2001, 05:00 PM | #22 | |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
Quote:
I think it will go in the 11.70's the way it sits, and with the 4:30's and rear and axles package I am doing this winter 11.40's. My Speedbrain shows 438FWHP @ 6350rpms and in the past it was only off 2HP on the dyno, that would be awesome! @ 375RWHP Did you get that oil pump shaft fixed?
__________________
D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R Check out RNH Performance Performance Engines and Custom Fabrication. From Mild to Wild we can build what you want, when you want it. FOR SALE Stainless Steel Torque Box Supports |
|
12-20-2001, 03:58 PM | #23 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
ported E7's all the way!
my mph should have me atleast in the high 12's, but traction and tranny problems (couldnt hammer 2nd or 3rd gear) held me back this year. A B303 cam (found cheap on Ebay, thats why ) and a fresh tranny will be in for spring and I'm hoping to hit 12.90's or better on drag radials. If not I'll slap on my slicks and make a run for it, hopefully not shatter my T-5 or axles
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
12-22-2001, 04:55 PM | #24 |
Registered Member
Join Date: Sep 1998
Location: Berea Ky
Posts: 17
|
My car goes 12.90@105 with edelbrock 6039 and performed 5.0 intake N/A
__________________
1986gt Vortech S-trim SQ,off road H-pipe,Edelbrock Intake, 1.7 rockers, 3.73gear,edelbrock 6039 cylinder heads and f303 cam. Best run so far 10.78@127.40 and 1.50 60 foot. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Head and intake flow. Something to think about. :) | 5ohCOUPE | Windsor Power | 3 | 03-16-2003 08:52 AM |
What head gaskets and intake gaskets?? | dragstang86 | Windsor Power | 4 | 12-20-2002 04:20 AM |
Speed Secret # 3 | jim_howard_pdx | Windsor Power | 13 | 11-09-2002 10:35 AM |
Head, Cam, Intake Combo.... | Bluefox91LX | Windsor Power | 2 | 10-20-2002 01:48 AM |
Head gasket or intake leak? | Frankenstang65 | Classic Mustangs | 9 | 09-14-2002 06:16 PM |