MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Poll: Which heads for a 393W
Poll Options
Which heads for a 393W

Reply
 
Thread Tools Rating: Thread Rating: 2 votes, 1.00 average. Display Modes
Old 09-16-2004, 10:15 PM   #1
red82gt
Sober voice of Reason
 
red82gt's Avatar
 
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
Default 393W-Which heads?

Okay, the 302 is dead-long story. I now have an F4TE longblock 351W with the F2TE rods. The block is at the machine shop being bored .030", line honed, new cam bearings and core plugs, and then it's getting a cleanup cut and when the pistons+crank arrive, we'll set the deck height. I'm going to go with the Scat 9000 3.85" stroker crank, the 351W rods and a dished piston (Either KB 12cc dish or SRP 14.5cc dish), the CR with a zero deck and 60cc chambers will be mid to high 10's. The assembly will be balanced with a pioneer damper and a good billet steel flywheel (won't be an Ebay cheapie). Headers will be 1 3/4" longtubes and I'll be using a Vic Jr. intake (already bought it) and a proform main bodied 800 double pumper carb. Cam will be a hydraulic roller (seeing as this is a factory roller block) and will be specd by one of the custom cam grinders (Ed Curtis or Buddy Rawls). It'll be backed up by a tremec TKO600 tranny and a built 8.8.
My goals for the car include:

1. runs on pump gas
2. fairly streetable ie-power brakes(hence the hydraulic roller)
3. Makes peak power before 6000 rpms (cast crank)
4. 120+ mph in the quarter with a 3200lb car (includes me @245 lbs).
5. No worries about emmissions-as long as it doesn't kill trees when I drive by them
I've excluded the AFR 205's due to the fact that they aren't readily available with hydraulic roller springs and their "bare" heads are really bare and would cost more to set up for hydraulic roller springs than complete solid roller spring heads and that's without the CNC work.
__________________
393W: AFR 205's, hydraulic roller, TKO600.
red82gt is offline   Reply With Quote
Old 09-16-2004, 10:26 PM   #2
~The Jester~
Rat Killer
 
~The Jester~'s Avatar
 
Join Date: Aug 2002
Location: Cold ass Ohio
Posts: 1,143
Default

I say CANFIELD, but I'm dying to see how John Kaase's new heads do, so my official vote is for Jeg's/Kaase.

They're already outlawed in EVERYTHING, but you didn't list a class specific legal car in your requirements. Big time canted valve heads, ready to bolt on with a hydraulic cam. Sounds awesome to me.
__________________
d-Con Racing
"Nothing fancy, just 347 inches of RAT POISON!"

MICE need not apply.....

~The Jester~ is offline   Reply With Quote
Old 09-16-2004, 10:50 PM   #3
red82gt
Sober voice of Reason
 
red82gt's Avatar
 
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
Default

I'm not against the Jeg's/Kaase heads but I almost feel guilty using something that awesome on a sub 6000 rpm motor. With their midlift #'s you could make some awesome midrange with the right cam. Would give me plenty of room to grow for my next project
__________________
393W: AFR 205's, hydraulic roller, TKO600.
red82gt is offline   Reply With Quote
Old 09-17-2004, 12:24 AM   #4
htwheelz67
Registered Member
 
Join Date: Aug 2004
Posts: 5
Default heads

I would go at least afr 185's, if you want real bigg power and still good velocity look at the TFS TW'r's, not many heads if any can beat it. checkout this http://www.airflowresearch.com/articles.htm and scroll all the way down you will find all the ultimate guides to cyl heads that MM&FF did in their magazine look at group 4 and 5 theres flow and dyno tests for each. As you will see just because a head has big flow doesnt mean it will make power. A stge 2 or 3 set of twisted wedge heads could be a good choice as well. I am building a 408 around the same as your 393 custom cam...etc and am having my TW's ported.

also see www.enginemasters.com and look at the 393 build under small block ford (2 parts) pretty impressive........


Good luck with your build, careful parts matching makes a world of difference and the custom cam is a great step but you will need head flow #'s first.

my 67 vert http://htwheelz.smugmug.com
htwheelz67 is offline   Reply With Quote
Old 09-17-2004, 12:43 AM   #5
red82gt
Sober voice of Reason
 
red82gt's Avatar
 
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
Default

The cam will be the very last item I get, as far as I'm concerned, this is the only way to do it I was looking at some of the porting packages for the trick flow heads and even the TFS high ports. Since I don't have headers yet, and I still have to buy pistons, I could still go all the way to TFS R heads.
Thanks, htwheelz67, good luck with your 408.
__________________
393W: AFR 205's, hydraulic roller, TKO600.
red82gt is offline   Reply With Quote
Old 09-17-2004, 08:14 AM   #6
Ieatcamaros
Domestic Rice really sucks!
 
Ieatcamaros's Avatar
 
Join Date: Apr 2002
Location: KY
Posts: 973
Default

I second the trick flow r's.
__________________
The sig says it all.
Ieatcamaros is offline   Reply With Quote
Old 09-17-2004, 10:14 AM   #7
420nitro
Registered Member
 
420nitro's Avatar
 
Join Date: Nov 2003
Location: Rockford
Posts: 596
Default Re: 393W-Which heads?

Quote:
Originally posted by red82gt
Okay, the 302 is dead-long story. I now have an F4TE longblock 351W with the F2TE rods. The block is at the machine shop being bored .030", line honed, new cam bearings and core plugs, and then it's getting a cleanup cut and when the pistons+crank arrive, we'll set the deck height. I'm going to go with the Scat 9000 3.85" stroker crank, the 351W rods and a dished piston (Either KB 12cc dish or SRP 14.5cc dish), the CR with a zero deck and 60cc chambers will be mid to high 10's. The assembly will be balanced with a pioneer damper and a good billet steel flywheel (won't be an Ebay cheapie). Headers will be 1 3/4" longtubes and I'll be using a Vic Jr. intake (already bought it) and a proform main bodied 800 double pumper carb. Cam will be a hydraulic roller (seeing as this is a factory roller block) and will be specd by one of the custom cam grinders (Ed Curtis or Buddy Rawls). It'll be backed up by a tremec TKO600 tranny and a built 8.8.
My goals for the car include:

1. runs on pump gas
2. fairly streetable ie-power brakes(hence the hydraulic roller)
3. Makes peak power before 6000 rpms (cast crank)
4. 120+ mph in the quarter with a 3200lb car (includes me @245 lbs).
5. No worries about emmissions-as long as it doesn't kill trees when I drive by them
I've excluded the AFR 205's due to the fact that they aren't readily available with hydraulic roller springs and their "bare" heads are really bare and would cost more to set up for hydraulic roller springs than complete solid roller spring heads and that's without the CNC work.
He-hee

Just copy my shyte!
420nitro is offline   Reply With Quote
Old 09-17-2004, 10:29 AM   #8
420nitro
Registered Member
 
420nitro's Avatar
 
Join Date: Nov 2003
Location: Rockford
Posts: 596
Default

Look it's real easy and simple to get what you want! Just need the $$$.
Heres the low down...
408 or bigger....because....
you can keep the rpm's down and shtye tends to live longer when only needed to spin up to 6,000 rpms or less to simply achieve your goal.
Hyd cam works fine now...because of low shift point.
10.5 to 1 compreesion. (Pump Gas)
Super Victor intake....needed...(out-of- the-box) because of larger cross section verses the victor jr intake. You need more cross section because of larger cubes. Victor Jr. would work but need a lot of porting work done. That requires more $$

TFS-R out of the box would be plenty!!!!
AFR-225 would be plenty as well and allow to run a smaller cam with same H.P output over TFS_R heads. hint-hint- better drivabilty too!
AFR 205, 185 doesn't have enough cross section in my opinion.

You need volume along with flow to run strong.
750 mighty demon would be more then enough with awsome low end throttle response..Why a 750 and not a 850-950 carb... only going to go 6,000 rpms.

End result.. a very fast street car on pump gas with a power range in the 3,000-6000 rpms!
420nitro is offline   Reply With Quote
Old 09-17-2004, 11:05 AM   #9
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Default

I absolutely love my Canfield heads.

They are expensive but the quality of the work is 2nd to none.
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim.
00' Lightning-Stock
88'CRX-13 second ego killer
Dark_5.0 is offline   Reply With Quote
Old 09-17-2004, 07:56 PM   #10
stang_racer20
Registered Member
 
stang_racer20's Avatar
 
Join Date: Jun 2003
Location: Wisconsin
Posts: 348
Default

Quote:
Originally posted by Ieatcamaros
I second the trick flow r's.
I was gonna say that as well. Third vote for TFR's.
__________________
92 Mustang GT, 347 Stroker(Forged Steel Crank/Rods-Balanced, Forged Aluminum Dished Pistons), Trick Flow Track Heat Intake, Trick Flow Twisted Wedge Heads w/ Stage 3 port/polish, 80mm C&L MAF, FMS 30# Inj., BBK AFPR, Trick Flow Stage 2 Cam, Trick Flow 1.6R Rockers, BBK E.L. Headers, Flowmaster Cat-Back, MAC CAI, FMS Pulleys, Griffin Alum. Radiator, MSD Pro-Billet Distributor; AOD, Dynamic 3300 Lockup Converter, B & M Super Cooler, B&M Ratchet Shifter; 3:73 gears.
stang_racer20 is offline   Reply With Quote
Old 09-18-2004, 04:04 PM   #11
fiveOguy20
Registered Member
 
Join Date: Sep 2002
Posts: 156
Default

my vote would either be AFR 225 or vic jr.
__________________
347- ported X heads, Xcam , RPM air-gap intake, 650 holley DP, 10:5 comp., equal lenght shorties, pullies, MSD ignition, pro 5.0 shifter. stock fuel system !!




best ET: 11.95 @113 1.64 60 foots
fiveOguy20 is offline   Reply With Quote
Old 09-19-2004, 08:29 PM   #12
ricechefmerkl
Registered Member
 
ricechefmerkl's Avatar
 
Join Date: Aug 2004
Posts: 40
Default

I gotta give another vote for the jegs/kaase heads I just get shivers when I see/read/think about them and when a set will be mine for my 427w , the kaase numbers a crazy so i raise both hands for them
__________________
83 capri t-top, tubular k-member,tubular control arms, coilovers, 408w, with 225cc pro cnc heads , merkl race shop c-6 trans etc shes coming together
79 burb 15.27`s at 90 mph 6800 pounds no juice do i need to say more
ricechefmerkl is offline   Reply With Quote
Old 09-20-2004, 09:20 PM   #13
red82gt
Sober voice of Reason
 
red82gt's Avatar
 
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
Default

Hmm, there's a good chance that I'd be the only one in my neck of the woods running these (jegs/Kaase). I'd normally run away from anything with ports close to that big but the midlift #'s blow everything else away (intake, at least). The classes around here that I'd be able to run don't have any any regulations over the heads. The price is right too. I'll let you guys know at the end of October when the money will be there for the heads......
__________________
393W: AFR 205's, hydraulic roller, TKO600.

Last edited by red82gt; 09-21-2004 at 02:20 PM..
red82gt is offline   Reply With Quote
Old 01-25-2009, 08:20 AM   #14
10sec80cobra
Registered Member
 
Join Date: Oct 2005
Posts: 3
Default Re: 393W-Which heads?

canfields all the way
10sec80cobra is offline   Reply With Quote
Old 02-27-2010, 01:04 AM   #15
talaposa
Registered Member
 
Join Date: Feb 2010
Location: California
Posts: 2
Default Re: 393W-Which heads?

A shame you don't look closer at the Afr 205. I have them on my 393W. The midlift air flow is about the best in the industry.
talaposa is offline   Reply With Quote
Old 03-22-2010, 09:28 PM   #16
capri351
Registered Member
 
Join Date: Apr 2009
Location: Wyo, casper
Posts: 4
Default Re: 393W-Which heads?

Edelbrocks are for chevys ... go trick flow
capri351 is offline   Reply With Quote
Old 09-14-2010, 02:23 AM   #17
mjacoby321
Banned
 
Join Date: Sep 2010
Posts: 15
Default Re: 393W-Which heads?

Canfield heads are the way to go! They may be expensive but the work done using canfields are simply superb.
mjacoby321 is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Help I need heads!! SmokinStangGT Windsor Power 18 05-04-2003 10:05 PM
New FRP Heads for 96 - 98 4.6 surfbeast Modular Madness 9 11-21-2002 07:02 PM
will 99-2002 cams out of the pi heads fit in the 96-98 stock heads slow98 Modular Madness 6 10-25-2002 04:28 PM
GT-40 heads 5.0 Pony Windsor Power 1 09-10-2002 10:26 PM
Which heads are beter? patman Classic Mustangs 3 12-02-1999 03:42 AM


All times are GMT -5. The time now is 01:34 PM.


SEARCH