Hybrid Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
06-28-2002, 07:32 AM
|
#1 |
|
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
Need a cowl hood?
If I install a 1 inch spacer on my holley intake, will I need a cowl hood?, or will it clear the stock hood?
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
|
|
|
06-28-2002, 08:30 PM
|
#2 |
|
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
anyone know?
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
|
|
|
|
06-28-2002, 11:28 PM
|
#3 |
|
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
well 1 inch is cuttining it close, but you may get away with it by cutting out the insulation on the hood but you can test it by putting a block of wood or something equivalent to 1 inch on the intake and see if it hits, or how close it comes. Good luck
__________________
|
|
|
|
|
06-29-2002, 01:01 PM
|
#4 |
|
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
on my 89lx, with the edelbrock rpm(1inch spacer) i needed a cowl hood. the stock one wouldnt even close.
|
|
|
|
|
06-30-2002, 12:42 AM
|
#5 |
|
Registered Member
Join Date: Aug 2001
Location: Ft. Worth, TX
Posts: 456
|
I am pretty sure that you will need one. The holley intake is not small. Why the one inch spacer? Are your valve covers that tall?
__________________
You're gonna need your seatbelt |
|
|
|
|
06-30-2002, 04:57 PM
|
#6 |
|
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
I got a set of brand new Motorsport tall valve covers for free, so I wanted to install them.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
|
|
|
|
06-30-2002, 11:46 PM
|
#7 |
|
Registered Member
Join Date: Aug 2001
Location: Ft. Worth, TX
Posts: 456
|
Oh, well then you will need the spacer like you said. I am pretty sure you have to use the 1" to clear those. I was just curious which covers you were using.
__________________
You're gonna need your seatbelt |
|
|
|
|
07-01-2002, 03:16 PM
|
#8 |
|
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
since you might have to get a new hood anyway. try and cut the supports out of the hood that sould give you about 1-1/12 more room to play with
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Cervinis cowl hood | Ieatcamaros | Windsor Power | 3 | 02-10-2004 07:55 PM |
| My Review on Motion Performance Parts Hoods | Fox Body | Blue Oval Lounge | 8 | 11-22-2001 05:10 PM |
| Help! Hood won't fit! Cowl hood guys please read! | daveGT | Windsor Power | 3 | 08-21-2001 07:49 AM |
| Cowl hood opening problems | Mach 1 | Windsor Power | 1 | 04-25-2001 07:49 PM |
| where to find a cowl hood for this........ | mikos chris | Windsor Power | 0 | 04-01-2001 02:53 PM |