

© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Sep 2002
Location: Dayton, OHIO
Posts: 73
|
![]() I was looking for a used block to start building but then I thought why not ask others who have been there.
I plan on staying under 400 horsepower with this motor and doubt if I will ever spray Nitrous into it and theres no supercharger in the works either. I will be going with either a 331 or 347 stroker kit and wanted to know what thoughts everyone had on a block to start out with? 1. Find a stock block to rebuild? Does it have to be a roller Mustang block? 2. Buy a new Ford block for like 300 bux? Seems like a good deal? Someone at the Colombus swap said to beware of 5spd. blocks because of crank end play?
__________________
93'GT 5spd. Underdrives, FMS clutch, adjustable quadrant,Flowmasters, Kenny Brown subframe connectors, 3.73 gears, Steeda Tri-Ax. JBA shorties, BBK h-pipe. More to come. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Aug 2002
Location: Canton, Ohio
Posts: 4
|
![]() I got what you looking for. Block is off from 1988 Lincoln LSC (same as Mustang and they are roller block). e-mail me for more information. poonracing@yahoo.com
Sam. ( Canton, Ohio ) |
![]() |
![]() |
![]() |
#3 |
gear banger
Join Date: Aug 2000
Location: CHICAGO
Posts: 1,144
|
![]() I would get a good used HO block and throw a 347 stroker kit in there. There is no reason to stay with a 331 if you are not going to spray, or blow it.
If you are going to stay around 400hp there is no need for a expensive forged kit either. You can get a basic stroker kit with I-beam rods, cast crank, and even hypertuctic pistons if you want. Throw in a set of main studs, and a girdle, and it will last a long happy life. Don't worry about 5-speed blocks having to much end play. If it is true the block has nothing to do with it. The thrust bearing is what determins crankshaft endplay and you will be geting a new one anyway.
__________________
79 Hatch: NA 347, Stage 2 Canfield Heads, Victor JR. Intake, Blueprinted Holley 750 HP, Solid Roller Cam, Shooting for 10's on motor 93 LX: Tremec, dual friction clutch, fms flywheel, Hedman shorties, O/R H-pipe Ricer hater's club member #49 |
![]() |
![]() |
![]() |
#4 |
motors done......woohooo
Join Date: Mar 2002
Posts: 799
|
![]() check out the chp, coast high performance kit (347) if its a daily driver i think this would be the 347 to go with, it has an offset piston pin, for reduced rod angle. and the 5.3 rod so the oil ring doesnt intersect with the pin bore. (havent heard of any problems with the oil ring in the pin bore, so you might get away with the 5.4 rod)
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Sep 2002
Location: Dayton, OHIO
Posts: 73
|
![]() Thanks for the info guys!
About this oiling problem I have heard mentioned from some manufacturers where the pin intersects the oil ring groove, Is this a myth ? It makes sense to me that you wouldnt want that pin thru the groove if at all possible.
__________________
93'GT 5spd. Underdrives, FMS clutch, adjustable quadrant,Flowmasters, Kenny Brown subframe connectors, 3.73 gears, Steeda Tri-Ax. JBA shorties, BBK h-pipe. More to come. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: May 2002
Location: Tampa,FLORIDA
Posts: 340
|
![]() I decided to go to the 351w block for the added strength, and added cubes. If you want to stay with the 302, 300 bucks is not bad for a new block.
__________________
5.0, Holley heads, 1.7 Scorp Rockers, Stealth intake, Holley 600 carb, Holley Mech. Fuel pump, MSD 6Digital, MSD distributor, Hotchkis upper/lower rear control arms, FMS B Springs, 3:73 (8.8) rear. Production # 9,377 |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Apr 2002
Location: Downers Grove, IL
Posts: 464
|
![]() A good used block is better in my opinion because it has been though heat cycles that some say make the block stronger. That, and when you're on somewhat of a budget, your 330 could be better spent. Just my opinion. ~Brian
__________________
1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59 |
![]() |
![]() |
![]() |
#8 | |
gear banger
Join Date: Aug 2000
Location: CHICAGO
Posts: 1,144
|
![]() Quote:
Myth
__________________
79 Hatch: NA 347, Stage 2 Canfield Heads, Victor JR. Intake, Blueprinted Holley 750 HP, Solid Roller Cam, Shooting for 10's on motor 93 LX: Tremec, dual friction clutch, fms flywheel, Hedman shorties, O/R H-pipe Ricer hater's club member #49 |
|
![]() |
![]() |
![]() |
Thread Tools | |
Display Modes | Rate This Thread |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rare Mustangs....Got One? | 1969Mach1 | Blue Oval Lounge | 22 | 09-25-2010 04:59 AM |
Speed Secret # 3 | jim_howard_pdx | Windsor Power | 13 | 11-09-2002 10:35 AM |
Alot of Questions About Modular Motors | vetteeatr | Modular Madness | 2 | 07-01-2002 03:44 PM |
85 5.0 block vs. 94 5.0 block (gas mileage) | jruppert | Windsor Power | 1 | 11-12-2001 07:15 PM |
Very bad experience with Engine Dynamics of San Jose CA | JAGraff | Small Ponies | 0 | 05-12-1999 02:27 AM |