![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Jun 2000
Location: Saudi Arabia
Posts: 130
|
![]() ????
------------------ 94 COBRA # 926/5009 TFS track heat heads (ported), Cobra intake (ported), 24# Injectors, 3/8" Phenolic spacer, E303 Cam, TFS 1.7 rr BBK 1 5/8" headers, BBK 65mm TB, Pro-M 80mm MAS, PIH kit w/ A9L computer, FMS 3.55 ratio BBK 190 lph fuel pump, Paxton fpr, MSD'S, March Pulley's, Pro-5 tower power shifter, Autometer shift light (5600), Intellitronix Air/Fuel gauge, Eibach Sportline Springs, Tokico 5-way adjustable, Granatelli Motorsport Subframe |
![]() |
![]() |
![]() |
#2 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() You're going to have to break out your DMM and spend the day checking circuits. 99% of the time, a code 66 is caused by one of the following:
Open MAF circuit, Open VPWR circuit to MAF sensor, Open PWR GND circuit to MAF sensor, MAF circuit shorted to ground, Faulty ECA or MAF sensor, Air leak before or after MAF sensor, MAF sensor disconnected. Those are the things you have to check. Take care, -Chris ------------------ Retired Moderator MustangNet My site: Peckerwoods Pit Stop ![]() My teams site: Jim Porter Racing RACECAR spelled backwards is RACECAR HEY !!! Are you ASE Certified ??? If you are, ask me about iATN. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2000
Location: Saudi Arabia
Posts: 130
|
![]() How to check the circuit ?
|
![]() |
![]() |
![]() |
#4 |
The Photoshop Guru
Join Date: Feb 2001
Location: Mecca, Indiana
Posts: 1,419
|
![]() I got the same code when I first got my car back together, along with some EGR codes, and a couple others. I don't know if the O2's were what was causing the problem, but before I changed the O2 sensors I cleared the codes and it kept coming back. I replaced my O2 sensors and reset the computer and cleared the codes again and it never returned. That was the only thing I did to the car.
------------------ Gunning for 12's! ![]() Buy your parts here ICQ# 42269241 |
![]() |
![]() |
![]() |
#5 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() The correct way to check them is with a break-out box, but since you probably don't have one, you will have to disconnect the harness at the ECM, and determine which wires are which, in relation to the MAF sensor wires, and check them for continuity, short to ground, or an open. You also must inspect the intake tubing before and after the MAF sensor, and make sure there is no air leaking in.
Take care, -Chris ------------------ Retired Moderator MustangNet My site: Peckerwoods Pit Stop ![]() My teams site: Jim Porter Racing RACECAR spelled backwards is RACECAR HEY !!! Are you ASE Certified ??? If you are, ask me about iATN. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Jun 2000
Location: Saudi Arabia
Posts: 130
|
![]() How to check MAF voltage, there are 4 pin. in the MAF harness ?
__________________
94 COBRA # 926/5009 TFS track heat heads (ported), Cobra intake (ported), 24# Injectors, 3/8" Phenolic spacer, CompCamsXteremeEnerge 224 232 555'' 565 112, CompCams Pro-Magnum 1.6 RR, BBK 1 5/8" headers, BBK 65mm TB, Pro-M 80mm MAS, Next Generation PIH kit w/ A9L computer, 3.55, BBK 190 lph fuel pump, Paxton fpr, MSD'S, March Pulley's, Pro-5 tower power shifter, Intellitronix Air/Fuel gauge, Eibach Sportline Springs, Tokico 5-way adjustable, Granatelli Motorsport Subframes, Edelbrock Mufflers, 2.5" exhaust system, Pfgoodrich comp T/A drag. Previous Mode: E303 Cam, TFS 1.7 rr '92 Integra LS. |
![]() |
![]() |
![]() |
#7 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() MAF wires, and what they are, what to test and what you should find:
A: Red wire, VPWR. This wire supplies battery voltage to the MAF. There are two tests to perform. First, check the wire for continuity from the MAF harness connector to the ECM. Second, check for battery voltage between the Red wire and ground, with the harness disconnected from the MAF, and with the Key On and the Engine Off (KOEO). B: Black wire, PWR GND. This wire is directly connected to the battery ground. There are also two tests here. For both tests, disconnect the harness from the MAF. With the key OFF, check for continuity between the Black wire and the negative battery post. For the second test, check for battery voltage between the Black wire and the positive battery post. C: Tan wire with a Light Blue tracer, MAF RTN. This wire delivers a signal back to the MAF from the ECM. It is a ground signal, but it is controlled by the ECM. Do not confuse this wire with battery ground, as it will not always be able to complete a circuit with another positive battery source. Test this wire for continuity between the MAF harness connector and the ECM. D: Dark Blue wire with an Orange tracer, MAF SIG. This is the wire that sends a signal from the MAF to the ECM. There are several tests for this wire. First, check this wire for continuity between the MAF harness conector and the ECM. Second, connect the DMM to this wire and to the Black wire, and check for infinite resistance. Third, connect the DMM to this wire and to the Tan wire with the Light Blue tracer, and check for infinite resistance. Finally, with everything connected and the engine running, use the positive DMM lead to back-probe this wire at the MAF harness connector , and touch the negative DMM lead to the negative battery post, and make sure that the DC voltage is between .2vdc and 1.5vdc. Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Code 81?? Code 51. HELP!! | blk88lx | Windsor Power | 0 | 03-31-2004 08:22 PM |
code 15 | tomazzzo | Windsor Power | 1 | 06-06-2003 11:15 PM |
Question about sensors and voltage | MustangGT1990 | Windsor Power | 6 | 02-06-2003 02:55 PM |
How To Clear An Air Bag Code | PKRWUD | Windsor Power | 13 | 03-28-2002 11:04 AM |
Code Trouble! Help! | Jeff7477 | Windsor Power | 3 | 07-03-2001 01:57 PM |