© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
01-02-2003, 06:16 PM | #1 |
Registered Member
Join Date: Apr 2002
Location: Florida
Posts: 532
|
Ready for roller rockers
I wanna get a set of 1.6 roller rockers for my gt40-p heads but I have a question how can I tell which set I need cause theres some a 7/16" stud mount or a 3/8", how can I tell what they are on my heads? Also ive been lookin at Crane's for $229 a set does this sound like a fair price? Also I need a part # on some new rods cause since the heads are off I figured I replace them.
__________________
90gt 347 and some bolt ons :-) RICE HATERS MEMBER #73 Last edited by Scrapla; 01-02-2003 at 06:24 PM.. |
01-04-2003, 10:56 PM | #2 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
the P heads are pedestal mount, you wont be able to use stud mount rockers unless you get the crane conversion kit for them.
I'd suggest getting a set of 1.6 pedestal mount roller rockers -drew
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
01-05-2003, 01:20 AM | #3 |
Registered Member
Join Date: Apr 2002
Location: Florida
Posts: 532
|
Can someone tell me a good name brand on them 1.6 pedestal mount rr's ive been lookin at some cranes but not sure, someone have some part#'s maybe?
__________________
90gt 347 and some bolt ons :-) RICE HATERS MEMBER #73 |
01-05-2003, 09:00 AM | #4 |
Registered Member
Join Date: Apr 2002
Location: Florida
Posts: 532
|
Ok its down to either Ford Motorsports or Crane, the cranes are actually like $10bucks cheaper.
__________________
90gt 347 and some bolt ons :-) RICE HATERS MEMBER #73 |
01-05-2003, 09:08 AM | #5 |
Registered Member
Join Date: May 2002
Location: Tampa,FLORIDA
Posts: 340
|
I am looking at the Scorpions for mine. My local speed shop (Gearheadfx.com) has em for $239. They are really nice. I had the cranes before but these look much beefier. Here is a pic of them. http://www.ralphsmachine.com/roller_rockers.html
__________________
5.0, Holley heads, 1.7 Scorp Rockers, Stealth intake, Holley 600 carb, Holley Mech. Fuel pump, MSD 6Digital, MSD distributor, Hotchkis upper/lower rear control arms, FMS B Springs, 3:73 (8.8) rear. Production # 9,377 |
01-05-2003, 12:24 PM | #6 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
well since my crane rockers are stamped with a ford oval, I'm guessing they are the same
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Dont use 1.7 rockers with stock heads? | Coupe5oh | Windsor Power | 10 | 11-28-2015 12:36 PM |
Rail Rockers on 289 Small Block Heads | sleeperstang | Classic Mustangs | 16 | 05-11-2003 11:34 PM |
Roller Rockers, bad? | HiFlow5 0 | Windsor Power | 1 | 04-14-2002 01:35 PM |
reg rockers or roller rockers?? | Chevysucks | Windsor Power | 1 | 12-05-2001 08:17 PM |
Rockers and thermostat | SlowStang2 | Windsor Power | 1 | 08-09-2001 06:44 PM |