© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-21-2001, 09:39 PM | #1 |
Registered Member
Join Date: Mar 2001
Location: Halifax Nova Scotia Canada
Posts: 12
|
easiest hp gains
whats the cheapest and easiest hp gains on a mustang 5.0ho 87-89? any freebies?
|
03-21-2001, 09:43 PM | #2 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
Timing, air silincer. The first mod any 5.0 should have is by far gears...
------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 13.012 Best MPH 104 Best 60' 1.816 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html |
03-22-2001, 10:43 AM | #3 |
Registered Member
Join Date: Mar 2001
Location: Halifax Nova Scotia Canada
Posts: 12
|
anything else? pulleys?
whats an air silincer? moving to the top. theres got to be some easy stuff that can be done on minimal cash. |
03-22-2001, 12:32 PM | #4 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
pulleys give the most bang for the buck.
|
03-22-2001, 01:11 PM | #5 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
yes underdrives are a very good gain for the money, the air silencer is inside the passenger side fender behind the air cleaner, it is supposed to quiet the incoming air but i didnt notice any difference when i took mine out, just take off the air cleaner assembly and there should be about 3 screws hodling it in there, remove those and pull the silencer out through the bottom, you will also want to advance your timing to about 14 degrees or so, the exhaust system is also very restrictive in these things, get an offroad h-pipe (little over $100) and you'll feel a noticable gain, then do the rest of the exhaust as money permits,
------------------ 88 Notchback 5.0, 3.73's, Explorer intake, pulleys, Crane 1.7's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air kit, motorsport wires, MSD coil, upper and lower control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best time- 13.99@99.75, not yet tested times after rocker and intake install |
03-22-2001, 01:15 PM | #6 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
If you have to pass emmissions, get a high flow cat H-pipe instead of the offroad, it'll give you more torque regardless. The first thing you should do is take out the air silencer though. Then get some better gears, 3.55 or 3.73, and underdrive pulleys.
|
03-22-2001, 09:37 PM | #7 |
Registered Member
Join Date: Mar 2001
Location: Halifax Nova Scotia Canada
Posts: 12
|
i really dont want to put the lower gears in, i like the cruising speed so im looking for making it up in the motor. how much compression am i running , and what hp on a stock 87 gt motor with headers
|
03-22-2001, 10:07 PM | #8 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
The first thing that we should have asked: How fast do you want to spend? In other words, would you be up for putting a few $1000 (er whatever the equivelant is in the Home Country) into your motor and then another 1k in your tranny to support that? Or are you looking for simpler things? The people here can help you plan out whatever you want. :-)
[This message has been edited by dinomite (edited 03-22-2001).] |
03-22-2001, 10:38 PM | #9 |
Import Slayer
Join Date: May 1999
Posts: 2,241
|
recovering5.0L, the factory HP rating for an '87 GT is 225 with 300 ft./lbs of torque.
Someome correct me if I am wrong but I think the compression is 9.2:1 ------------------ '82 GT 351W,BBK shorties, Comp Cam,edelbrock intake 625 cfm carter carb. c-4 tranny w/ pro stick shifter. 4 core radiator Mallory distributor. 3:27 ......................... |
03-22-2001, 10:52 PM | #10 |
Registered Member
Join Date: Mar 2001
Location: palmbayFL
Posts: 184
|
15 degrees timing is the best gain for no buck!
|
03-23-2001, 12:35 AM | #11 |
Registered Member
Join Date: Oct 2000
Location: new hope, pa
Posts: 1
|
hey heres one that always gets over looked. switch to an electric fan set up. the loss of the drag from the fan on the crank can be good for an easy 10 hp on relatively stock car. flax-a-lite makes a kit for specifically for the mustang...has a pricetag of just under $200 from summit
|
03-23-2001, 10:09 AM | #12 |
Registered Member
Join Date: Jan 2001
Location: oklahoma city oklahoma USA
Posts: 9
|
Bypass your coolent line on your egr plate all you do is connect the rubber hoses that run into the egr plate it runs hot coolent though there it will help
|
03-23-2001, 10:10 AM | #13 |
Registered Member
Join Date: Jan 2001
Location: oklahoma city oklahoma USA
Posts: 9
|
oo yea if no emissions take off your smog pump and get the shorter belt this will also free up some poneys
|
03-23-2001, 02:42 PM | #14 | |
Registered Member
Join Date: Mar 2001
Location: Halifax Nova Scotia Canada
Posts: 12
|
Quote:
|
|
03-23-2001, 05:25 PM | #15 |
Registered Member
Join Date: Mar 2001
Location: palmbayFL
Posts: 184
|
BUY a CHILTON'S
|
03-23-2001, 10:14 PM | #16 |
Import Slayer
Join Date: May 1999
Posts: 2,241
|
I don't know for sure where the EGR coolant line is but I do know where the smog pump is.
If you are looking at the engine from outside the car, the smog pump is located under the alternator. Not directly under but you know what I mean. Or this: Locate the water pump, alternator, and power steering pump and the crankshaft pully and whatever is left is the smog pump. ------------------ '82 GT 351W,BBK shorties, Comp Cam,edelbrock intake 625 cfm carter carb. c-4 tranny w/ pro stick shifter. 4 core radiator Mallory distributor. 3:27 ......................... |
03-23-2001, 10:26 PM | #17 |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
The lines that are described above are on the EGR spacer which is right between the throttle body and upper intake. You will se two rubber lines going into each side of it. Remove the lines, get a connector, and connect the 2 lines together. Now there will be no hot coolant flowing through the EGR which will result in a cooler intake charge.
The electric fan is not worth as much as you think from what I've hear. It only has negative effects below 3000rpm's, above that the clutches release and the fan free wheels without drag on the motor. At the strip your RPM's shouldn't fall this low anyway, so you won't see much if anything at all at the strip- but this is just what I've been told, I may be wrong. I do believe that an electric fan is still a good idea anyway. If you get one and plan on running at the strip, I would also hook it up so that it could be turned on while the motor is off- this will draw cool air through the radiator cooling the fluid in it, plus it will blow air over the motor. This will benefit you at thr track. JFYI- Pulleys, 14* timing, offroad X pipe, mufflers, HD clutch, and 3.73's knocked 7 tenths from my ET and I gained 4.89mph on street tires. ------------------ 95 GT convt' 5 speed, 3.73's,FMS HD clutch, Pro 5.0 shifter, ASP alum. underdrive pulleys, Bassani offroad X pipe, 2 chmbr flowmasters, K&N w/o silencer, edelbrock performer intake, FRPP 65mm T-body, FRPP shorty headers, FRPP aluminum driveshaft.Hooker 4pt chrome car bar, Xenon/Wings West ground effects, custom interior Best ET: 13.83 Best MPH: 98.55mph with Best 60': 1.91 on Nitto DR's Homepage: <A HREF="http://www.angelfire.com/pa2/killercanary" TARGET=_blank>http://www.angelfire |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Jet Hot power gains? | Rev | Blue Oval Lounge | 7 | 09-02-2004 05:56 PM |
"Positive HP & TQ Gains - SVT Cobra?" | SVT30 | Modular Madness | 18 | 05-22-2003 02:35 PM |
PI WRHP GAINS ON 96-98 stang ? | southernstang97 | Modular Madness | 2 | 03-25-2002 02:06 PM |
Mac Pro-Chamber real gains on a '97? | Try Me | Modular Madness | 4 | 12-21-2001 10:27 AM |
HP and Torque gains | 01Snake | Modular Madness | 3 | 10-15-2001 11:35 PM |