MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar Mark Forums Read

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 07-24-2007, 09:19 PM   #1
WendyH
Registered Member
 
Join Date: Jul 2007
Location: Western Massachusetts
Posts: 3
Question Check Engine Light going on - need some help

Hi, need some help. I have a 95 5.0 and my check engine light has been going on. There are three codes showing - 172, 181 and 189. I know this has something to do with the engine running lean, but does anyone know exactly what the codes mean? Also, any suggestions on how to fix?

Thanks
WendyH is offline   Reply With Quote
Old 07-31-2007, 07:36 PM   #2
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: Check Engine Light going on - need some help

172 - o2 Sensor sensor circuit indicates system lean (right side)
181 - Right side still lean, at richest adaptive limit, during part throttle
189 - Left side still lean, at richest adaptive limit, during part throttle

Definately showing a lean condition so we'll start with the obvious fuel possibilities.
When's the last time you changed your fuel filter?
Do you have any fuel mods, ie injectors, adj regulater, large fuel pump....?
How old are the 02 sensors, may be time to replace them.
Make sure your air filter and MAF are clean, if the MAF doesn't read all of the air coming in, the engine will think it doesn't need as much fuel going in, when in fact the 02 sensors are saying the opposite.
When was your last tune up?
Lsat but not least, have you made any changes at all before this started? Change octane in gas, use platinum plugs, anything at all?
__________________
USMC302 is offline   Reply With Quote
Old 08-10-2007, 08:10 AM   #3
WendyH
Registered Member
 
Join Date: Jul 2007
Location: Western Massachusetts
Posts: 3
Default Re: Check Engine Light going on - need some help

Hi, thanks for your reply.

I just had the fuel filter changed, platinum plugs put in, etc. I don't have any fuel mods. I also just had a new exhaust pipes / cats done and had the O2 sensors changed. Here is a big issue though, when I bought the sensors from Advanced Auto they said the car needed 4 sensors - 2 upstream and 2 downstream. The H pipes only had place for 2 and the mechanics put in the downstream sensors. Not sure that I have the correct sensors installed and can't find what is correct.

I recently put in a KN air filter, but haven't done anything with the MAF.

I have owned this car for 4 years and have always put in 93 octane.

After having the complete tune-up, putting in the new air filter and having the exhaust system done, the car still didn't pass inspections (emissions).

Any ideas? My regular mechanic couldn't figure out what to do about the codes, so he recommended someone. I'll be bringing the car in next week, but would love to have some more information before I do that.
WendyH is offline   Reply With Quote
Old 08-10-2007, 10:04 AM   #4
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: Check Engine Light going on - need some help

Two things I would change....Platinum plugs, throw them out and put in some autolites, next, go back to advanced auto and tell them they gave you the wrong sensors or harness for them, your right about only having 2. If you use a harness for four sensors, the signal will be reporting four a/f ratios and two of them aren't in so they're seeing no fuel now(hence the ECU reporting a lean condition), get the one for just the two sensors. I would bet lots of money that is your problem....
__________________
USMC302 is offline   Reply With Quote
Old 09-21-2008, 01:00 PM   #5
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: Check Engine Light going on - need some help

up stream sensors measure fuel downstream are there to measure if the cats are cleaning the exhaust fumes.with out the upstream sensors inthe right spot they wont measure fuel
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 09-21-2008, 01:37 PM   #6
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: Check Engine Light going on - need some help

Thanks Goodyear, hopefully, she's not still having this problem. lol
__________________
USMC302 is offline   Reply With Quote
Old 03-18-2009, 07:45 AM   #7
jmdesales
Registered Member
 
Join Date: Mar 2009
Posts: 2
Default Re: Check Engine Light going on - need some help

I know this post is super old but if you stumbled on here, RE: MAF, Remove MAF, spray the wire element inside the MAF down with brake cleaner, wait 15 min to dry completely, the wire will look and perform good as new. Do not stick a spray straw too close that you might touch the wire, if you break the wire element you will need a new MAF.
jmdesales is offline   Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
check engine light scott armstrong Modular Madness 1 07-29-2002 09:10 PM
Check Engine Light afeezor97 Modular Madness 8 07-09-2002 11:28 AM
Check Engine Light 96GTPRT Modular Madness 5 05-20-2002 07:48 PM
Check Engine Light abesmith69 Windsor Power 1 02-21-2002 11:31 AM
Check Engine Light (What's new) rolling96 Modular Madness 2 06-25-2001 05:50 PM


All times are GMT -5. The time now is 07:08 PM.


SEARCH