Cobra Rotors

03-21-2001, 09:45 AM

I have a 95GT, can I install the 13" 95 Cobra rotos on the front and rear of my car? I'm not sure what the stock size is, I believe it's 11" front 10" back.

Thank You!

[This message has been edited by 5.0SN95GT (edited 03-21-2001).]

dinomite · 03-21-2001, 12:57 PM

They should slip right onto your current spindles. You need 17in wheels though.

spinemup · 03-21-2001, 01:01 PM

this is a joke right???? 13" rear disk? no you can't do that. you need front brackets calipers and rotors off of a 95 cobra in order to do the swap up front though

03-21-2001, 01:46 PM

I have stock 17 inch rims. spineup- All I need is the Cobras front brackets calipers? So there is no way to put bigger rear rotors?

03-21-2001, 10:37 PM

Basically you can upgrade to the cobra braking system, 13" rotors in the front and i believe 11.25" rotors in the back, or go custom aftermarket.... my advise, you cant be going that fast that you would need THAT much stopping power in the back, so go with the cobras rotors, they look good and performance will meet your needs im sure.

------------------
'93 Gt, Stock as a rock, but plan an AOD to T-5 swap, steeda tri-ax shifter, 3.55's, cobra intake, gt-40 irons, e303 cam, 1.6 rr's, mac headers, off road h-pipe, flowmasters cat back, msd ignition, blaster coil, mac cold air box (fenderwell), eibach springs, silver cobra r's, and an obnoxiously large mustang in the back window =0)

03-22-2001, 07:17 AM

Ok, I'll look into after market brake kit.

Thanks

dinomite · 03-22-2001, 01:37 PM

Whoops, didn't notice that you said rear. spinemup is right, the 13"s will go right on your current spindles up fron, but you will also need new calipers. In the rear, they are 11.25" rotors from the cobra, those are good enough. One route is the M-2300-k kit in your FRPP catalog, you do have one of those, don't you? BTW, are you doing road racing? If not, this is a pretty expensive setup just for the strip......

03-21-2001, 09:45 AM	#1
5.0SN95GT Guest Posts: n/a	Cobra Rotors I have a 95GT, can I install the 13" 95 Cobra rotos on the front and rear of my car? I'm not sure what the stock size is, I believe it's 11" front 10" back. Thank You! [This message has been edited by 5.0SN95GT (edited 03-21-2001).]

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
will 15x8 draglites clear 11.65" cobra rear rotors??	dragstang86	Windsor Power	1	08-01-2003 08:30 AM
98 Cobra wheel with Lincoln rotors?	88COBRA	Windsor Power	0	07-21-2001 06:48 PM
2001 Cobra Over Rated AGAIN!!!?!?!!! Wassup Ford?	KillaZ350	Blue Oval Lounge	24	06-29-2001 05:24 PM
93 Cobra Front Rotors	RMARIANI	Windsor Power	2	04-14-2001 01:19 PM
Salaeen, Shelby, Cobra please define these for me.	Taqus	Blue Oval Lounge	3	01-17-2001 02:39 AM

03-21-2001, 12:57 PM	#2
dinomite The Dude Join Date: Feb 2001 Location: Arlington, VA Posts: 1,262	They should slip right onto your current spindles. You need 17in wheels though.

03-21-2001, 01:01 PM	#3
spinemup Registered Member Join Date: May 2000 Location: middleboro,ma, usa Posts: 734	this is a joke right???? 13" rear disk? no you can't do that. you need front brackets calipers and rotors off of a 95 cobra in order to do the swap up front though

03-21-2001, 01:46 PM	#4
5.0SN95GT Guest Posts: n/a	I have stock 17 inch rims. spineup- All I need is the Cobras front brackets calipers? So there is no way to put bigger rear rotors?

03-21-2001, 10:37 PM	#5
Bangin Gears Guest Posts: n/a	Basically you can upgrade to the cobra braking system, 13" rotors in the front and i believe 11.25" rotors in the back, or go custom aftermarket.... my advise, you cant be going that fast that you would need THAT much stopping power in the back, so go with the cobras rotors, they look good and performance will meet your needs im sure. ------------------ '93 Gt, Stock as a rock, but plan an AOD to T-5 swap, steeda tri-ax shifter, 3.55's, cobra intake, gt-40 irons, e303 cam, 1.6 rr's, mac headers, off road h-pipe, flowmasters cat back, msd ignition, blaster coil, mac cold air box (fenderwell), eibach springs, silver cobra r's, and an obnoxiously large mustang in the back window =0)

03-22-2001, 07:17 AM	#6
5.0SN95GT Guest Posts: n/a	Ok, I'll look into after market brake kit. Thanks

03-22-2001, 01:37 PM	#7
dinomite The Dude Join Date: Feb 2001 Location: Arlington, VA Posts: 1,262	Whoops, didn't notice that you said rear. spinemup is right, the 13"s will go right on your current spindles up fron, but you will also need new calipers. In the rear, they are 11.25" rotors from the cobra, those are good enough. One route is the M-2300-k kit in your FRPP catalog, you do have one of those, don't you? BTW, are you doing road racing? If not, this is a pretty expensive setup just for the strip......