© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
06-12-2001, 02:29 PM | #1 |
Registered Member
Join Date: Feb 1999
Location: Camarillo/Thousand Oaks Ca
Posts: 223
|
Comp ratio ???
i recently got motor running again anf i had the heads milled.. i have a question about my comp ratio... what is it the heads were milled .030 and the block was also decked dunno how much mut i guess the normal decking, that would usually happen, well i know that stock comp is about 9:1 what would it be now with a 62cc head....?????
help???? ------------------ ALL NEW PPG Torch Red 95GT, 304ci block, Forged pistons, Ported Explorer Intake, E-303 cam, fully ported and polished and milled E-7 heads, 75mm MAS, BBK Adj. fuel Reg & gauge, BBK Shorty Headers, BBK H-pipe, March Pulleys, 2 Chamber Flowmasters, Kenny Brown 6 point Roll cage, Kenny Brown Panhard Bar, Powerslot Rotors, PBR twin piston calipers, Eibach Sportline Springs, 180* Thermostat, 1/2 Plenum Spacer, MSD 6AL, MSD Master Blaster, MSD 8.8 Wires, 24# Racing Injectors, AFS 10.5" Cobra R's, Nit |
06-12-2001, 03:37 PM | #2 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
I dont know exactly. My best guess would be that since you decked the block and milled the heads you should be around 9.8:1.
Going to bakersfield with us friday? Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, headers and 3chamber flows. 12.55@107mph 50-175 Nitrous Works WET Kit just added. |
06-13-2001, 01:34 AM | #3 |
Registered Member
Join Date: Feb 1999
Location: Camarillo/Thousand Oaks Ca
Posts: 223
|
I wish i could but i gatta work......
|
06-14-2001, 08:34 PM | #4 |
Registered Member
Join Date: Feb 1999
Location: Camarillo/Thousand Oaks Ca
Posts: 223
|
any more guesss???????????
|
06-14-2001, 08:48 PM | #5 |
Registered Member
Join Date: Oct 1998
Location: Rogers, MN
Posts: 2,089
|
I'd say you shaved off 2.5 CCs. I guess that would make it about 9.3:1.
|
Thread Tools | |
Display Modes | Rate This Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How Can You Tell If Its Forged Also How to tell comp ratio??? | vetteeatr | Windsor Power | 0 | 11-08-2002 03:27 AM |
GOT A 351..stroke it? rod ratio q's | LX XLR8R | Windsor Power | 5 | 10-25-2001 08:58 AM |
Whats the best way to tell if your running lean or rich? | K.C. 5.0 | Windsor Power | 9 | 09-10-2001 03:04 PM |
Comp. ratio question with 58/54cc heads on stock bottom end.. | Killercanary | Windsor Power | 5 | 02-06-2001 03:51 PM |
Highest comp. ratio on pump gas? | Shawn | Classic Mustangs | 2 | 07-19-1999 11:27 AM |