D.S.S. MOTORS

1BAD89 · 06-25-2001, 08:14 PM

My latest 5.0 mag. has specs on all these crate engines. The D.S.S. bullet 306(power adder)has 404hp and 365lbs of tq at the motor, they said that is good for 11.30-40 E.T.'s. And wih a 150 shot of nitrous it is a mid to low 10 second engine. The GT40 crate motor puts out 302hp and 330lbs of tq very disappointing to me, as they claim 345hp with the bolt-ons they listed. But I went to D.S.S.'s web site and they have a 396w motor for like $6299 or around there. And I know it would make more hp and tq, and probaly be stronger for nitrous? What all woul I need for the swap? Anything special? I know headers, and the usual, fuel pump, inectors. But what kind and what sizes? But then again if the 306 motor from them runs 11.30's all motor, and 10's with nos, what more could you ask for, plus it's a $1000 cheaper than the 396, give me your thoughts. Thanks. Oh andone other thing I just bought a new SD T-5 it would not last very long on a 10 second or 11 second would it? And would you guys recommend a Tremec, if so what kind?

------------------
3:55's,BBK Off-Road H-pipe,BBK jet-hot coated equal length shorty headers,BBK 70mm Throttle Body,BBK adjustable clutch quadrant,C & L 76mm Mass air meter,Cobra R's 17x9 w/ 245's,Trick Flow Intake,Flowmaster Force II exhaust system, Super Duty T5,Centerforce II Clutch,Heavy Duty Radiator,9mm Ford racing plug wires,Accel cap and Rotor

http://www.geocities.com/i8urvpr/JM.html?987369348700

1BAD89 · 06-26-2001, 06:02 PM

.

[This message has been edited by 1BAD89 (edited 06-26-2001).]

stangbang · 06-26-2001, 07:28 PM

I think that the 396 is a stroked 351 and so there would be a little more involved in swapping it. Different headers ,brackets for a.c.,power steering,etc.You would also need a taller hood. I personally have a 347 stroker from CHP. I'm running 30lb injectors,C&L 76mm mas,Holley SystemaxII heads&intake.I am running a rebuilt t-5 but i know that this engine could easily scatter the trans.I would go with the tremec

n20lx · 06-27-2001, 10:03 PM

I'm running a DSS 331. These guys seem like they know theie $hit. If you tell them what ypour goal is (n20 for example), they will build your motor with that in mind. I have seen people post on this board that DSS just puts out cookie cutter motors right off the sheflf, but that was not the way mine was done. Mine was built to order. How your car runs depends on the whole system mass air to the slicks. Make sure you've got it all covered. My car is only running 11.90's. It should be much quicker, but I can only turn 6200 rpm & have a 3.73 gear. The T-5 I have came from D&D it's just a 2.95 gear special. It has stood up to a beating for many years including 5500 rpm launches & 1.5X 60' times.

06-25-2001, 08:14 PM	#1
1BAD89 Tubbed and Juiced Join Date: Mar 2001 Location: Tulsa, Oklahoma Posts: 1,861	D.S.S. MOTORS My latest 5.0 mag. has specs on all these crate engines. The D.S.S. bullet 306(power adder)has 404hp and 365lbs of tq at the motor, they said that is good for 11.30-40 E.T.'s. And wih a 150 shot of nitrous it is a mid to low 10 second engine. The GT40 crate motor puts out 302hp and 330lbs of tq very disappointing to me, as they claim 345hp with the bolt-ons they listed. But I went to D.S.S.'s web site and they have a 396w motor for like $6299 or around there. And I know it would make more hp and tq, and probaly be stronger for nitrous? What all woul I need for the swap? Anything special? I know headers, and the usual, fuel pump, inectors. But what kind and what sizes? But then again if the 306 motor from them runs 11.30's all motor, and 10's with nos, what more could you ask for, plus it's a $1000 cheaper than the 396, give me your thoughts. Thanks. Oh andone other thing I just bought a new SD T-5 it would not last very long on a 10 second or 11 second would it? And would you guys recommend a Tremec, if so what kind? ------------------ 3:55's,BBK Off-Road H-pipe,BBK jet-hot coated equal length shorty headers,BBK 70mm Throttle Body,BBK adjustable clutch quadrant,C & L 76mm Mass air meter,Cobra R's 17x9 w/ 245's,Trick Flow Intake,Flowmaster Force II exhaust system, Super Duty T5,Centerforce II Clutch,Heavy Duty Radiator,9mm Ford racing plug wires,Accel cap and Rotor http://www.geocities.com/i8urvpr/JM.html?987369348700

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Quarter window motors...	Hozer 88GTConv	Windsor Power	3	04-12-2003 09:40 PM
FFW to allow Mountain Motors in Pro 5.0??? Why?	Eric4Nitrous	Racer's Club House	15	07-19-2002 07:26 AM
Alot of Questions About Modular Motors	vetteeatr	Modular Madness	2	07-01-2002 03:44 PM
89 convertible window motors?	Drew	Windsor Power	2	06-05-2001 02:09 PM

06-26-2001, 06:02 PM	#2
1BAD89 Tubbed and Juiced Join Date: Mar 2001 Location: Tulsa, Oklahoma Posts: 1,861	. [This message has been edited by 1BAD89 (edited 06-26-2001).]

06-26-2001, 07:28 PM	#3
stangbang Registered Member Join Date: Oct 1999 Location: brunswick,ohio Posts: 135	I think that the 396 is a stroked 351 and so there would be a little more involved in swapping it. Different headers ,brackets for a.c.,power steering,etc.You would also need a taller hood. I personally have a 347 stroker from CHP. I'm running 30lb injectors,C&L 76mm mas,Holley SystemaxII heads&intake.I am running a rebuilt t-5 but i know that this engine could easily scatter the trans.I would go with the tremec

06-27-2001, 10:03 PM	#4
n20lx Registered Member Join Date: Sep 1998 Posts: 495	I'm running a DSS 331. These guys seem like they know theie $hit. If you tell them what ypour goal is (n20 for example), they will build your motor with that in mind. I have seen people post on this board that DSS just puts out cookie cutter motors right off the sheflf, but that was not the way mine was done. Mine was built to order. How your car runs depends on the whole system mass air to the slicks. Make sure you've got it all covered. My car is only running 11.90's. It should be much quicker, but I can only turn 6200 rpm & have a 3.73 gear. The T-5 I have came from D&D it's just a 2.95 gear special. It has stood up to a beating for many years including 5500 rpm launches & 1.5X 60' times.