MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar Mark Forums Read

Notices


Reply
 
LinkBack Thread Tools Rate Thread Display Modes
Old 10-08-2002, 07:39 PM   #1 (permalink)
302crew
Registered Member
 
Join Date: May 1999
Location: sloatsburg
Posts: 261
Default does this make sense

i jsut finished my combo and i am having major oil problems. i have two breathers on the valve covers and whenever i beat on the car oil blows either out the oil pan or rear main seal not sure but its one of those. cant tell cause the morroso pan is big an i realy can't see up in there to well all i know is that it is comming down the back of the oil pan. so im figuring it must be building up pressure when i beat on it. Is there a way i can get rid of this. and also i dont have a dipstick i pluged the whole off and have a bolt in the side of the oil pan till i get my new dipstick. is the dipstick supposed to be a vent for the crankcase. if anyone has a suggestion why this is happening i would be very thankfull or if anyone has a solution would be even better
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right

Last edited by 302crew; 10-08-2002 at 09:00 PM..
302crew is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 08:28 PM   #2 (permalink)
Maroon 5.0 LX
Registered Member
 
Maroon 5.0 LX's Avatar
 
Join Date: Mar 2001
Location: Southern Maryland
Posts: 471
Default

What'd he say?
__________________
'89 LX 5.0 - 5 speed. Original Owner
'94 E-150 4.9 Hi-Top Conversion Van
'06 Mustang V-6, 5 speed
Maroon 5.0 LX is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 09:46 PM   #3 (permalink)
fiveOguy20
Registered Member
 
Join Date: Sep 2002
Posts: 156
Default

Are u sure its not comin out of that whole u plugged...
fiveOguy20 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 10:21 PM   #4 (permalink)
PKRWUD
Junior Member
 
PKRWUD's Avatar
 
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
Default

What kind of oil pump do you have?

Did you remove the baffles from inside the valve covers?

Are you sure it's not the gasket/silicone at the back of the intake?

Take care,
~Chris
__________________
Webmaster:
Rice Haters Club
Jim Porter Racing
Peckerwoods Pit Stop


Support Your Local
RED & WHITE!
PKRWUD is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 10:41 PM   #5 (permalink)
302crew
Registered Member
 
Join Date: May 1999
Location: sloatsburg
Posts: 261
Default

im positive its not the back of the intake or the valve covers its a stock oil pump and yes the baffels are still in they are aftermarket fms valve covers and no its not comming out the dipstick hole and i just changed the rear main seal but like i said it only leaks alot when i beat on the car and it leaks for a while when it just sits in my garage not even running
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right
302crew is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 10:57 PM   #6 (permalink)
PKRWUD
Junior Member
 
PKRWUD's Avatar
 
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
Default

Are you POSITIVE you put all the rings on correctly (correct side facing up)?
__________________
Webmaster:
Rice Haters Club
Jim Porter Racing
Peckerwoods Pit Stop


Support Your Local
RED & WHITE!
PKRWUD is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 11:08 PM   #7 (permalink)
302crew
Registered Member
 
Join Date: May 1999
Location: sloatsburg
Posts: 261
Default

are you reffering to the rings on the pistons i would hope they are on corectly a rebutable machine shop put my bottom end together and i have about 150 psi of compression and yes i just put the rear main seal in
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right
302crew is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-08-2002, 11:33 PM   #8 (permalink)
mustangII460
Factoy Five Roadster
 
mustangII460's Avatar
 
Join Date: May 2000
Location: Sevier Co,Tennessee
Posts: 1,681
Default

I have had trouble with morroso pans leaking.

Also if your end play is way out on your crank it will often blow out the rear main seal. Ask the shop what the end play was on your crank.
__________________
Frank
mustangII460 is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-09-2002, 02:07 AM   #9 (permalink)
302crew
Registered Member
 
Join Date: May 1999
Location: sloatsburg
Posts: 261
Default

the end play on the crank was fine
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right
302crew is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Old 10-09-2002, 08:12 PM   #10 (permalink)
302crew
Registered Member
 
Join Date: May 1999
Location: sloatsburg
Posts: 261
Default

do you think it could be the gasket in the back of the oil pan is Fed up and when i beat oin it the oil is pressed against it and it just drips alot cause oil likes to drip forever
__________________
306 edelbrock 6037 heads full mac exuast 1.7 rr 373 rear hd clutch tremec mighty demon 650 carb msd ignition rpm air gap intake custom cam still trying to get it to run right
302crew is offline  
Digg this Post!Add Post to del.icio.usBookmark Post in TechnoratiFurl this Post!
Reply With Quote
Sponsored Links
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



Similar Threads
Thread Thread Starter Forum Replies Last Post
My whole sense of speed is now skewed... ChesteR Blue Oval Lounge 4 09-28-2001 07:52 AM
What cheap bolt-on can I make next? Gautam Blue Oval Lounge 2 09-24-2001 12:32 PM
What will make my 98 gt faster than 98 cobra Eminent18 Modular Madness 3 05-27-2000 04:24 AM
To make a cobra Eminent18 Modular Madness 2 05-26-2000 10:21 AM
does anybody make 90/10's for 96 up cars jameshensler Modular Madness 3 11-20-1999 07:46 PM


All times are GMT -5. The time now is 10:46 PM.


SEARCH