DYNO results today!!!!!
 

Howdy guys....haven't been around in a while. Well, I have spent the last 2 1/2 weeks on vacation and driving the wheels off of my car. I have put 2400 miles on my new motor....I wanted to get about 3000, but with the track closing next weekend and my vacation over, I wanted to get it going now so I called Coast and my motor builder and they said it would be O.K. So this morning I am heading down to the dyno do tune the baby in.

I romped a little on it last night....MAN THE POWER. It is so fun, I kinda need bigger tires now. I got on the turnpike and nailed it in 3rd at about 4000 and got sideways and before I knew it I was up to about 120 in 4th. I love it.

I will post results later today when I get back.

------------------
Dustin
89 Saleen GT Sport,347, TFS Street Heat Intake(port matched),TFS TW Heads(Stage 2),TFS #2 cam,BD-11A 9 psi,Crane 1.6 rr's,BBK 70mm TB,Pro-M 80mm MAF,MSD 6BTM, FMS 9mm wires,BBK longtubes,BBK Short H-pipe,American Thunder cat back,3.55's

12.3@119 street tires OLD MOTOR

11.496@121.08slicks OLD MOTOR

Good luck, Dustin! I can't wait to see the numbers on your new motor...they should be very strong. http://www.mustangworks.com/msgboard/smile.gif

E

------------------
1991 5.0 LX Coupe - 38,000 miles

13.17 @ 106.14 mph w/ 2.138 60'

Good luck on the dyno!!! Where is this dyno located at? Just curious because I am currently living in Tulsa, OK and was wondering if there were any good dyno's close by.

So where's the results http://www.mustangworks.com/msgboard/wink.gif

I am thinking over 500-530RWHP, going off the numbers on the last set-up.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon!
[b]12.16 @ 113.5, 1.78

Lets have it!!!


And they say Powerdynes suck! http://www.mustangworks.com/msgboard/biggrin.gif

------------------
1988 Mustang GT
11.8 @ 123 (7/14/01)
11.5 @ 120 (9/14/01)
1992 BadAzz Wrangler
1993 Explorer

See my car at: www.mustangworks.com/cgi-bin/moi-display.cgi?179

No, they Blow! http://www.mustangworks.com/msgboard/biggrin.gif

------------------
1989 lx notch
89,000 miles
5-speed, bolt-ons, 3.73, TFS TWs, TFS Track Heat, TFS Stage 1 cam

Ok guys....sorry for the delay, I was at the shop for 6 hours doing different things....pretty interesting, disappointing and good.

I did 12 runs with the blower hooked up and 3 with it unhooked just to see how the Stroker performed.

My first run was a dog, but what can you expect with a new motor.

Run 1
Max HP: 463.3 rwhp
Max TQ: 491.5 rwtq

I did some tuning, set my timing at 13* with my boost retard at 2 FP at 47psi.

Run 4
Max HP: 492.5 rwhp
Max TQ: 518.1 rwtq

Yadda yadda yadda, more tunung, some lost power here, some more power there, here is my best run. I set my timing at 12* and my BTM at 1*, set my fuel pressure at 49 psi and let 'er rip....here it is.

Run 10
Max HP: 516.4 rwhp
Max TQ: 553.0 rwtq


Here is the disappointing part.

I took my blower belt off making the blower useless, just a free air port, bumped my timing to 18 and dropped my fp to 45 psi.

My best run N/A
Run 15
Max HP: 376.3 rwhp
Max TQ: 412.8 rwtq

Now I am extremely mad that I only gained 140 hp with 9 lbs of boost. I guess it is the blower but I am happy overall. I am making roughly 600 fwhp and 647 rwtq.

Now I am just worried about my "new" tranny holding up.

This weekend I am going to the track to see what all I can break, so I will keep you posted. The analyzer says I should run 10.80's @ 125-127 mph. I doubt it though.

C-ya later.

------------------
Dustin
89 Saleen GT Sport,347, TFS Street Heat Intake(port matched),TFS TW Heads(Stage 2),TFS #2 cam,BD-11A 9 psi,Crane 1.6 rr's,BBK 70mm TB,Pro-M 80mm MAF,MSD 6BTM, FMS 9mm wires,BBK longtubes,BBK Short H-pipe,American Thunder cat back,3.55's

12.3@119 street tires OLD MOTOR

11.496@121.08slicks OLD MOTOR

Those numbers look good to me.

What RPM did the horsepower peak at? Also, what size headers and H-pipe are you using?

------------------
1989 lx notch
89,000 miles
5-speed, bolt-ons, 3.73, TFS TWs, TFS Track Heat, TFS Stage 1 cam

Those are some nice numbers. Unfortunately the power you achieved during your best run will not stay since your computer will adapt out the extra fuel you added by raising the fuel pressure. The upside is that you know that your engine will run better with a richer air/fuel ratio. You can get a chip burned or buy an SVO extender to tweak that so it stays.

Do you have a power graph that you can scan in and post?

------------------
351W 89 Mustang GT Convertible

Well 140hp for 9psi isn't too bad in my opinion. A stock car will pick up about 10hp per psi, so you're doing much better than that. http://www.mustangworks.com/msgboard/smile.gif

I think your numbers are great. Even N/A, I think they are very impressive. I may have missed it earlier, but what are the specs on your motor? I guess I could go to user rides, but I'm just lazy today http://www.mustangworks.com/msgboard/biggrin.gif

Overall, I would be very happy with the numbers. Just imagine 11 or 12 lbs. of boost. Jeeeezzz! BTW - what kind of "new" tranny do you have behind that monster?

Good luck at the track...with all of the power you are making, you probably won't be able to really get on it until the 1000' mark! http://www.mustangworks.com/msgboard/biggrin.gif

E

------------------
1991 5.0 LX Coupe - 38,000 miles

13.17 @ 106.14 mph w/ 2.138 60'

Wow! I need a blower on my 347. If I had your hp I would be running low 9s!

------------------
88 347, Twisted wedge heads,Comp Cams 224/230 cam, 1/4=10.324 @ 126.95, 60' = 1.394 http://xs-fx.com/raughammer/larrysample.htm

I think those numbers look good Dustin, a bigger blower that feeds that motor more air will make big HP, the BD-11 is just out of breath and the motor is using everything it can take, I'd be happy.

I think the tranny will live if you ease it out of the hole and don't power shift it, if you turn 125 with a decent 60 you'll go low 10.40's--10.30's. Good Luck let me know how it goes.

Jim- My phone lines at home are all screwed up so I can't get on at night, I did just get the Speedbrain ECU on mine since Dad went to a PMS..I'll let you know how it does.

------------------
Check Out My Site 91GT,[bSpeedbrain ECU[/b],Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,30#,76mm C&L,75mm Accufab, Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 33 splines coming very soon!
<B

Your #'s are very impressive Dustin....I'd be thrilled. Man, that thing is gonna really haula$$ at the track - my guess is that you'll pull a 10.6 @ 123 http://www.mustangworks.com/msgboard/biggrin.gif Good luck, and let us know how it goes!

------------------
'90 5.0 LX - heads, intake, cam, fuel delivery, gears, full exhaust, pulleys, ignition, drag springs, front brake upgrade, a/c delete, K&N cone filter charger.......and much more!
1/4 mile: 12.29 @115
60': 1.78

Those #'s are damn impressive. I hope I never pull up beside you at a light http://www.mustangworks.com/msgboard/eek.gif

Good luck at the track

------------------
88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft)

John R. mustang,***Good luck on the dyno!!! Where is this dyno located at? Just curious because I am currently living in Tulsa, OK and was wondering if there were any good dyno's close by.

You live in Tulsa, Oklahoma? So do I, drop me a PM. B.J.S. has a dyno, Ed wright, and a few other places here in Tulsa by the way.

------------------
-1989 GT, not stock.
-2000 Camaro SS-A4,
-1989 Chevy S-10, EX. Cab-383, RPM air-gap intake, demon carb., tubbed, trick flow TW heads, trick flow pistons, 6" rod's, etc... autometer phantom gauges, "built" 700R4, roll cage, lexan back window, corbeau seats, R.H.S. 5 harnesses, Fuel cell, convo pro wheels, 15x14's with 29x18.5 M/T'S on back, 15x4's on front, nitrous, 4 inch cowl hood, Ford 9", auburn Pro-series Posi, Pro-billet distributor, Sanderson Jet-hot coated headers, Custom radiator,