© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
05-14-2002, 02:22 AM | #1 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
TFS TW, milling 1.7's and E303
Im surfacing my TFS TW heads. I believe the max lift is .535? or .530? Im going to run E-303 w/ 1.7s which is 530 lift?
AM I safe? Skyler
__________________
2001 BMW M3 6spd 12.79@108 RIP ---- 1993 Notch w/ 98 4V 4.6 Fasttt... -1989 Saleen Mustang #406- 12.32@109 -1999 Black Cobra Coupe- JBA Shorties, Bassani Cat-X, Magnaflow 3", Pulleys, 85mm Pro-M, Ported Intake, Soild Rear w/ 4.30s, Tubular Front End, X2C arms, 13lb batt, few others. |
05-14-2002, 10:57 AM | #2 |
Resident Redneck
Join Date: Jan 2002
Location: Cecil County, MD
Posts: 165
|
Dude, the lift would be like .529. It should work fine. But, to be sure just clay your pistons. Good Luck.
-Billy
__________________
95' GT: 306, XL Ross Pistons, Ultra Lite H-beam Rods, Forged Scat Crank, 28oz Romac, 28oz JW flexplate, FTI ported RPM II intake, FTI ported AFR 165's, FTI custom cam, 75mm BBK Throttle body, 80mm Pro-M, 4800 PI stall, PA Super Comp AODE, Strange 33 spline race axles, Strange ultra lite spool, Motive lite 4.30's, Strange rear race brakes, Mega bite seniors, double adjustable uppers w/spherical bushings, Racecraft anti-roll bar, LPW rear end girdle, Metco d/s loop, A9L conversion, AFM PMS |
05-14-2002, 11:52 AM | #3 |
Registered Member
Join Date: Jan 2002
Location: Va
Posts: 1,122
|
You shouldn't have any problems...if i was you why not change cams? The E-303 isn't that good of a performance cam. Try the lunati 2031 or something of that nature..I think you'll be more happy.
Eric
__________________
68 Camaro Gene Fulton 632ci Two stages of Jug 8.41 164mph Rockingham 1-26-03 |
05-14-2002, 06:18 PM | #4 |
Registered Member
Join Date: Feb 1999
Location: Utica, Michigan
Posts: 2,631
|
Some people run pretty decent with an E-303 cam.
The max lift for TW's is .540 if I remember correctly. My heads have been resurfaced twice, and I use the E-303 with 1.72 Motorsport (Crane) Rockers, and a 6.70 inch pushrod. No clearance issues here. |
05-14-2002, 06:21 PM | #5 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Sounds good thats what I was looking to hear.
__________________
2001 BMW M3 6spd 12.79@108 RIP ---- 1993 Notch w/ 98 4V 4.6 Fasttt... -1989 Saleen Mustang #406- 12.32@109 -1999 Black Cobra Coupe- JBA Shorties, Bassani Cat-X, Magnaflow 3", Pulleys, 85mm Pro-M, Ported Intake, Soild Rear w/ 4.30s, Tubular Front End, X2C arms, 13lb batt, few others. |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
E303 cam install? | bailey_57 | Windsor Power | 11 | 04-19-2004 01:59 AM |
50 HP Cam Swap? Replace E303 with Comp XE270 | NO SLO PK | Windsor Power | 2 | 07-01-2003 04:52 PM |
Grr, this e303 cam is frustrating in my 95stang | chickendreamer | Windsor Power | 5 | 04-10-2003 05:12 PM |
Need opinions..NOVI 1000 with E303 and Longtubes?? | 88COBRA | Windsor Power | 13 | 01-03-2002 12:45 AM |
E303 with this setup | stng87 | Windsor Power | 3 | 03-14-2001 08:26 PM |