e7's on a sedan motor?

bailey_57 · 04-06-2009, 08:03 PM

ok back when i was young and stupid i ran the oil out of my engine in my 83 capri, threw a rod through my oil pan and in need of a vehicle with little funding i replaced my 68 302 with a recon 85 sedan motor. engine runs well with only about 5000 miles on it since it was installed 9 YEARS AGO! i got sick of the car nickel and diming me and entered the world of aero nose 5.0's. anyway out of nostalgia i've brought the cat back out of retirement. here's the question, i'm keeping the motor in tha car regardless. i have a set of ported e7's that i wanted to bolt on the car. they aren't decked or anything crazy. can i bolt these on my sedan motor right now with no problems? also how hard is it to install a non roller cam in a car? break in procedures, etc. i'd just like to add some pop to it. thanks

goodyear1984 · 04-11-2009, 09:15 AM

yes they will bolt on.the cam goes int the same as a roller but u have to brake it in or u can burn the lobes or real quick

04-06-2009, 08:03 PM	#1
bailey_57 Registered Member Join Date: Mar 2000 Location: Berwick,Pa Posts: 127	e7's on a sedan motor? ok back when i was young and stupid i ran the oil out of my engine in my 83 capri, threw a rod through my oil pan and in need of a vehicle with little funding i replaced my 68 302 with a recon 85 sedan motor. engine runs well with only about 5000 miles on it since it was installed 9 YEARS AGO! i got sick of the car nickel and diming me and entered the world of aero nose 5.0's. anyway out of nostalgia i've brought the cat back out of retirement. here's the question, i'm keeping the motor in tha car regardless. i have a set of ported e7's that i wanted to bolt on the car. they aren't decked or anything crazy. can i bolt these on my sedan motor right now with no problems? also how hard is it to install a non roller cam in a car? break in procedures, etc. i'd just like to add some pop to it. thanks __________________ '89 GT hatch back performer rpm intake, performer rpm cylinder heads, fms e-303 cam, kirban adj fp regulator, holley 65mm tb, harland sharp 1.6 roller rockers, alum driveshaft, 3.73 gears (283 rwhp, 303 rwtq new numbers with new heads)

04-11-2009, 09:15 AM	#2
goodyear1984 Registered Member Join Date: Dec 2006 Location: new york Posts: 482	Re: e7's on a sedan motor? yes they will bolt on.the cam goes int the same as a roller but u have to brake it in or u can burn the lobes or real quick __________________ 347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters ^best et so far 11.6 1.61 60ft coming soon 9sec et's 1992 mustang gt 2001 gmc 1500 4x4 78 century boat 92 skidoo

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ported e7's?	bailey_57	Windsor Power	28	07-15-2004 07:54 PM
Could I use 71 351C valvesprings on my e7's?	crazypete	Windsor Power	1	07-15-2004 10:43 AM
F303 and E7's	Ieatcamaros	Windsor Power	9	10-31-2003 03:46 PM
home porting E7's	Skywalkr57	Windsor Power	4	07-30-2002 06:08 PM
92 Mustang LX Sedan 2.3L	Mustang LX	Small Ponies	3	06-16-2000 03:39 PM