![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
|
Thread Tools | Rate Thread | Display Modes |
|
![]() |
#1 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
![]() R/T... .923
60.... 2.307 330... 6.373 1/8... 9.740 MPH... 73.46 1000.. 12.618 1/4... 15.068 MPH... 92.17 Thats With a Bad Spin, 2500rpm Slip & No Powershifting. I Will Be Racing Next Friday & Saturday, So I NEED To Break 14s. I Have New Tires In My Room, But I Dont Know If They Will Do Much More For Traction. Also, I Have BBK 1-5/8" Equal Legnth Shortys In My Room, But Am Waiting To Do My Whole Exhaust At Once. Any Little Driving Tips, Or Any Other Tips??? Thanks. ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
![]() |
![]() |
![]() |
#2 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() If you are running Street Radials drive off the line DO NOT LAUNCH, go out of the hole easy then roll into the throttle. A set of DOT's like ET STREETS will get you there as well. I went 13.20's on radials, then I went 12.87 on the DOT's with the stock motor.
------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! [b]12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jan 2001
Location: Maryland, USA
Posts: 16
|
![]() Are you icing your intake down? If not, throw a couple of ice bags on your intake and throttle body and let it get real cold. That will do it!
------------------ Too much for this site to let me list! ![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
![]() i didnt ice my intake down, ill try that for next week.
i cooked my dinner on my intake though!! i am going to the parts shop, and looking for some cheap mods..... maby underdrives?? Would That lower my time .1?? thanks. ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Nov 2000
Location: Milwaukee,Wisconsin
Posts: 380
|
![]() 1.What's timing set at?
2.Did you pull the front swaybar? 3.Make some home-made ram air. Just get an air conditioning/heating duct and some tubing and route it up the fenderwall to the airbox. 4.Pull the front seat out. It's easy on mine. 5.What kind of fuel pressure do you have? Try unplugging the vacuum line to the fuel pressure regulator for more pressure. ------------------ '91 LX convertible , T-5, Lakewood driveshaft safety loop,Centerforce Dual Friction, FMS adjustable cable w/quadrant, 3:55's(not installed yet), ported/polished/milled E7 heads, 1.6rr, 1.94/1.60 stainless valves, March Performance Pulleys and A/C Eliminator, short belt, Home Depot ram air, K&N, battery in trunk, removed swaybar, glasspacks w/turndowns, 225/50/16 Re 730's |
![]() |
![]() |
![]() |
#6 |
Conservative Individualist
Join Date: May 1997
Location: Wherever I need to be
Posts: 7,487
|
![]() That 2.30 60 foot time is killing you.
A better launch will knock off a tenth, easily. Practice, practice, practice. Powershifting is also worth a tenth but risky if you mess up. Just watch the tach, shift hard and fast @ 5200 - 5400 RPM on a stock 5.0. A good launch and correct shift points should have you in the 14's with ease. More: Try advancing the timing to 14 or 16 degrees. Free and can be worth a tenth. Easily reversed, too. Use 92 octane (or higher) gas. Do an oil change and use synthetic oil. Also worth a tenth. Like Stangin88 mentioned; A cooled (iced) intake is worth a tenth, too. Now you're in the mid 14's. See, this was easy! That'll be $10. please. ![]() |
![]() |
![]() |
![]() |
#7 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() no one mentioned airing up the front tires, air them up to 45-50psi, but dont forget to take them back down after you leave the track, this will reduce the friction between the tires and the ground and thus make them easier to move, every little bit helps
also if your REALLY desperate (like the time a ran a 14.02 and BADLY wanted to break into 13's) you can pull your serpentine belt, but take the belt and tool that you use to take it off with you so you can put in back on AS SOON as you get off the track, it will easily give you 1-2 tenths, i did it and hit a 13.9X on a worse 60ft than the 14.02, so i know it works pretty well but i wouldnt reccomend you doing it very often good luck, hury up and get rid of those gears and shoot for 13's!! ------------------ 88 Notch, B&M Ripper, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframes, 65mm TB, March ram air ,MSD coil, U/L control arms, 155lph f/p, Crane Adj.FPR, Nitto drag radials, best 1/4--> 13.76@101.4 on a 2.17 60ft |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Jun 1999
Location: Walker, MI, USA
Posts: 1,202
|
![]() I Stripped the car down and got aleats .1 better
![]() ------------------ 14.28@103.0 on a G-Tech Engine: Steal Mounts, Under drive pulleys, K&N, Home ported Lower Intake, No power steering, No A/C Drive Train: 3.55, World Class T-5, NOW it is time for Real power STUFF I Have and will put on after I get everthing: Mac cold intake, 70MM TB, Valve covers (COOL ONES)255 Fuel pump NOS Dry 75HP. Next to get: rocker arms,Cam,TFS Heads,Injectors 26,Holley intake, What might I need??? See It at <A HREF="http://www.computerconquest.com" TARGET=_blank>www.computer |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Apr 1999
Location: Pittsburgh, Pennsylvania
Posts: 73
|
![]() You've gotten some great advice here. As mentioned don't try to launch out on street tires, drive it out. With street tires I get the best 60' with a SLIGHT bog while slipping the clutch.
With that MPH, 1/8 and 1/4 , it looks to me like you are shifting too early. If I shift at 5K MPH is like 95-96, if raised to 5.5K it goes to 97-98. This is with the stock tach. Don't take this the wrong way but IMHO you could easily go a tenth (or more) faster by modifying your driving style. It's also cheaper than buying a another part. Good Luck! PS: GEARS! |
![]() |
![]() |
![]() |
#10 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
![]() simply not spinning will do it, most definently. if you really did have bad spin, i bet you can pick up .2-.3 if you don't spin.
|
![]() |
![]() |
![]() |
#11 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
![]() Well, I Shift At 5000rpm every gear on the stock tach, but will my 175xxx km engine hold up with 5200-5500 rpm shifts???
I Will Slip the clutch from about 1800rpm, Sift at 5200-5300rpm and see if that makes a difference. i spun pretty bad every run i made, but that was with my 2500rpm slip. i hope to get 14s next friday ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: May 1999
Posts: 5,246
|
![]() Take it to 5500rpm by the stock tach and see what happens.
I shift my 250,000km car at 5800rpm on the stock tach. |
![]() |
![]() |
![]() |
#13 | |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
![]() Quote:
P.S.- When I was running 15.02 at 91.5mph in my car, bumping the timing from 10 to 13* netted me three 14.96's in a row, so this alone given everything else (like the weather) is the same, will net you you're 14 second slip UNDRDOG- Do you race at Keystone? I'm there every week in my 95 canary yellow convertible (though I haven't been running for a few eeeks due to a T-5 that's on its last leg), my dad is there in his white 12 second 91GT, and my mom spectates in her '01 BULLITT. If you see us there come on over and say hello! ------------------ 1995 NA GT CONVERTIBLE BEST ET: 12.92 BEST MPH: 106.85 AFR's, FTI cam, edelbrock intake, EEC TUNER and lots more. http://www.angelfire.com/pa2/killercanary |
|
![]() |
![]() |
![]() |
#14 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
![]() he SHOULD try different shift points, as the stock tach is notoriously off, so shifting at 5500 could be 5200 or 5800 as well. short of getting a new tach, the only way i can think of to find out how much yours is off is to run it to the limiter.........(don't do that)
|
![]() |
![]() |
![]() |
#15 |
Registered Member
Join Date: Apr 1999
Location: Pittsburgh, Pennsylvania
Posts: 73
|
![]() Something that I forgot about is that my eng. is not 100% stock,although it's not far from it. It's got an edelbrock performer intake and 1.7RR's and upgraded valve springs, UD crank pulley and 3.55 gears. Everything else is stock. (hedrs.,mass air,TB,etc.) Even though you are stock try going a little higher (5200-5300). Or if you can get a good tach and check it against the stock one. Do a compression check and/or leakdown test to see what condition everything is in, if everything checks out OK I wouldn't worry about it. The only reason I suggested working on driving is that from what I've seen alot people think they drive well when they really don't. Then they think it's the car so they throw money at it and get mad because their car isn't "running like it should". My first run at the track was 15.2 at 93 mph. After some practice with NO changes to the car I've run a best of 14.06 at 99 mph. My goal this year is 13.xx, with good tires I believe it's possible. I'm no expert by any means, just trying to help. Killercanary, yes, I go to keystone, usually on thurs. for test and tune. I think I've seen your car there before. Is your dads car all white with M/T's and A/C delete? My car is a dark blue '90 GT. I'll probably be there next week so I'll look for you. Good luck with your trans. |
![]() |
![]() |
![]() |
#16 | |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
![]() Quote:
------------------ 1995 NA GT CONVERTIBLE BEST ET: 12.92 BEST MPH: 106.85 AFR's, FTI cam, edelbrock intake, EEC TUNER and lots more. http://www.angelfire.com/pa2/killercanary |
|
![]() |
![]() |
![]() |
#17 |
Guest
Posts: n/a
|
![]() All good advice.....+ I'd let the air out of your rear tires at the track - I run about 20 psi in my rear and I'm able to launch nice and hard. Good luck, I don't think you'll have a problem w/ getting mid-high 14's.
------------------ '90 LX 5.0;12K original miles (no sh*&);3.55 gears; March pulleys;Edelbrock Performer Heads;BBK 1 5/8" equal length shorties;MSD 6AL ignition w/ blaster 2 coil;FMS E303 cam;Pro-M 75mm MAF;BBK 70mm TB; Eibach drag-launch spring kit;Southside welded subs;9" K&N cone filter charger;Hurst shifter;Cervini's 3" turbo hood;A/C delete; gutted cats;2 chamber Flomasters;Corbeau racing seats;FMS 30# injectors;JMS chip; Holley 190lb fp;TFS track heat Intake (12.299 @ 113 - 1.78 60') |
![]() |
![]() |
#18 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
![]() oh ya, i was shifting into 4th with my 308 gears & 26"tires at 5k according to the stock tach.
i was told by unit that i should keep it in 3rd. how much should i improve by keepong it in 3rd??? thanks |
![]() |
![]() |
![]() |
#19 |
Registered Member
Join Date: Jun 2001
Location: Quebec canada
Posts: 92
|
![]() Stay in third and go get that 14 second timeslip. Good lock!
|
![]() |
![]() |
![]() |
#20 |
Registered Member
Join Date: Nov 1999
Location: Altoona, PA
Posts: 336
|
![]() Yes, if you do in fact have 3.08's, you should be crossing in 3rd. Right there in eliminating that shift, you'll have your 14 second pass with no problem. Combine all the above and you may see a 14.8 or so when its all said and done.
------------------ 1995 NA GT CONVERTIBLE BEST ET: 12.92 BEST MPH: 106.85 AFR's, FTI cam, edelbrock intake, EEC TUNER and lots more. http://www.angelfire.com/pa2/killercanary |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
IFS drop spindles on 65-66? | 65modified | Classic Mustangs | 15 | 01-29-2007 06:06 AM |
BANG! why is neutral drop better? | gtsr515 | Windsor Power | 10 | 10-12-2006 11:54 PM |
How easy is it to install 3.73 gears? | Beanhead | Windsor Power | 22 | 10-10-2003 03:55 PM |
K & N drop in filters...questions... | MineralGray02K | Modular Madness | 3 | 07-18-2002 09:08 PM |
Anyone drop in a stroker or big block? | sgwinn | Windsor Power | 2 | 08-01-2001 11:52 PM |