![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Mar 1999
Location: Canada
Posts: 66
|
![]() I am going to buy some new heads very soon but I'm torn between the Edelbrock and Trick Flow heads. I was told to go with either the 1.60/1.90 performers or the 1.60/2.02 trickflows. I'm not going to do any other upgrades this year asides from heads and have mac 1 5/8 shorties as the only other upgrades.I also don't want to flycut the pistons.Asides from the new heads everything will stay stock for this year. Help please.
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 2001
Location: cohutta georgia
Posts: 43
|
![]() I went with the edelbrocks.
------------------ 85 mustang coupe with a 88 block,edelbrock 6022 aluminum heads,crane roller rockers,aluminum driveshaft,C-4 trans,3500 stall,3.73 gears,lakewood traction action liftbars with air bag in right rear spring,longtube headers,flowmasters, weiand stealth intake,600 holley, best e.t. 1/8 mile 8.10 best mph. 85.20 best 60 foot 1.73... |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Apr 1999
Location: MO
Posts: 79
|
![]() I am happy with my Edelbrock Performer RPMS.. but also upgraded alot of other things as well.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Feb 2001
Location: Berkshire County - Massachusetts
Posts: 735
|
![]() I went with the edlebrock's for my 392 stroker buildup. I've heard that I might have made a bad mistake due to the large cubes v. relatively low flow #'s. The heads are very nice though, and my engine builder is very satisfied. tThe motor is going together in about 2 weeks so I'll let you know.
------------------ In progress for Spring: 93 GT less motor and tranny, 8 pt cage, chute, Sothside Machine bars & Sub-frames, 3.73's '69 393 stroker Edlebrock Performer heads, Performer RPM Upper & Lower Manifold..Crane Gold 1.6 Rollers..BBK 70MM TB & cats..30lb Injectors..Cartech Fuel System.. |
![]() |
![]() |
![]() |
#5 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() None of these people have given you any reasons as why to choose their head. So maybe you should listen to me here. I went with the TFS head after some research. Bigger valves, and MUCH better flow numbers. You dont have to take my word for it, check out www.fordmuscle.com they have many aftermarket 5.0 heads all flowtested on their site.. The TFS pretty much comes out on top. Not to mention they will run with high timing and low octane gas, which is pretty nice considering the spiking gas prices.
You can see my motor combo, VERY simple, and still smog legal, and runs 12.5's in a fairly heavy chassis. Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, headers and 3chamber flows. 12.55@107mph Going for 11's on 87 octane with A/C and 20+MPG!!! |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Apr 2001
Location: cohutta georgia
Posts: 43
|
![]() well the reason I picked the edelbrocks is because everyone that I talked to that had the edelbrocks said that they have had them for anywhere from a year to four years without any problems. trickflows make good power no doubt but I don`t think they have the quality of the edelbrocks.
|
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: May 1999
Location: Georgia
Posts: 3,866
|
![]() Edelbrocks are easier to install, much higher quality, and a good street head. Trick flows are a little cheaper, flow better, and make a little more power, depending on your application.
Want do you want? I would go with the AFR's at this point, they are real nice, although a little pricey. ------------------ 1993 GT/AOD '93 Mustang GT |
![]() |
![]() |
![]() |
#8 |
Sniffed too much n20
Join Date: Oct 1998
Location: Ont, Canada
Posts: 1,018
|
![]() It all depends on what you want to do. Trick Flows are cheaper, but they don't compare to Edelbrock's quality. If you spend the little extra on the TFS then you'll have a good set of quality heads. The Edelbrocks flow quite well, not as much as the TFS, and still make great power across the RPM band.
I'm really happy with my Edel. 6032's, I'm glad I went with them, I know that the TFS would have made more, but really I didn't need that. I wanted good streetability and reliability. Hope that helps. |
![]() |
![]() |
![]() |
#9 |
Guest
Posts: n/a
|
![]() The quality of the casting of the Edelbrocks is better, & if you want to hog them out in the future, they respond very well to porting.
------------------ 91 coupe 3.73's,long tubes,2 1/2" exh,ported stock t-body,ProM-77mm cobra intake,edelbrock heads,B303,1.72 rr's 36lb inj's,tremec, & a Paxton NOVI 2000!!! 11.020 @128.95 on BFG Drag Radials (275/60/15) |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Edelbrock Performer 5.0 Heads | white91gt | Windsor Power | 1 | 08-03-2004 12:18 PM |
Edelbrock 5.0 or Trick Flow Street? | Bad89stang | Windsor Power | 6 | 11-19-2002 12:00 PM |
Torque specs for trick flow heads? | Coupe5oh | Windsor Power | 1 | 03-16-2002 09:25 AM |
Trick Flow heads??? | AB89GT | Windsor Power | 10 | 09-06-2001 05:57 PM |
Trick Flow Cams? | 86GT | Windsor Power | 5 | 01-11-2001 08:31 PM |