Engine compartment wiring

glxstang · 06-16-2002, 05:35 PM

I pulled out my engine and tranny today and labeled all the wiring. The problem is that the wiring is all cracked, aftet all it's almost twenty years old. I can't put this crap back in with all my hard work on the rebuild and painting the engine compartment. My question is what have all of you done in this case where you want to replace the wiring.

Thanks for your input!

PM

LX5liter · 06-17-2002, 09:30 AM

You could probably buy a new harness. there is a few companies out there who sell them I'm sure. (Painless Wiring???)

glxstang · 06-17-2002, 11:27 AM

I checked with painless...They don't carry harness wiring for a 83.....

Thanks though....

RPM427 · 06-17-2002, 02:44 PM

Rip off all the old split loom tubing and replace it with new split loom from Radio Shack. Then you can wrap all the junctions and ends with eletrical tape. It will looks like the factory harness if done correctly.

You could also route the harness in the fenderwells and in the cowl. That will really clean up the engine compartment.

06-16-2002, 05:35 PM	#1 (permalink)
glxstang Registered Member Join Date: Feb 2001 Location: Delray Beach, Florida Posts: 97	Engine compartment wiring I pulled out my engine and tranny today and labeled all the wiring. The problem is that the wiring is all cracked, aftet all it's almost twenty years old. I can't put this crap back in with all my hard work on the rebuild and painting the engine compartment. My question is what have all of you done in this case where you want to replace the wiring. Thanks for your input! PM

06-17-2002, 02:44 PM	#4 (permalink)
RPM427 Registered Member Join Date: Aug 2001 Location: Huntington NY Posts: 573	Rip off all the old split loom tubing and replace it with new split loom from Radio Shack. Then you can wrap all the junctions and ends with eletrical tape. It will looks like the factory harness if done correctly. You could also route the harness in the fenderwells and in the cowl. That will really clean up the engine compartment. __________________ -1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out!

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rare Mustangs....Got One?	1969Mach1	Blue Oval Lounge	18	11-12-2007 01:34 AM
Very bad experience with Engine Dynamics of San Jose CA	JAGraff	Classic Mustangs	8	06-16-2005 12:43 PM
Very bad experience with Engine Dynamics of San Jose CA	JAGraff	Site Talk	0	05-12-1999 03:30 AM
Very bad experience with Engine Dynamics of San Jose CA	JAGraff	Small Ponies	0	05-12-1999 03:27 AM
Very bad experience with Engine Dynamics of San Jose CA	JAGraff	Racer's Club House	0	05-12-1999 03:27 AM

06-17-2002, 09:30 AM	#2 (permalink)
LX5liter dude5l Join Date: May 2001 Location: Grande Prairie, Alberta, Canada Posts: 603	You could probably buy a new harness. there is a few companies out there who sell them I'm sure. (Painless Wiring???)

06-17-2002, 11:27 AM	#3 (permalink)
glxstang Registered Member Join Date: Feb 2001 Location: Delray Beach, Florida Posts: 97	I checked with painless...They don't carry harness wiring for a 83..... Thanks though....

Sponsored Links