AN fittings

dherrer1 · 01-23-2001, 11:26 AM

Can someone explain to me the numbering scheme for AN fittings. What does a 6 AN mean? 6 millimetes ID or OD or what....

Thanks

FoxBuilder · 01-23-2001, 12:27 PM

AN (Army-Navy) number simply stands for 16 ths of an inch, so -08 = 8/16" which = 1/2"

------------------
1984 Mustang Top Fueler with Flowmaster's

dherrer1 · 01-23-2001, 01:26 PM

Quote:

Originally posted by FoxBuilder:
AN (Army-Navy) number simply stands for 16 ths of an inch, so -08 = 8/16" which = 1/2"

Thanks for the education... is the number for a inner dimension or an outer?

FoxBuilder · 01-23-2001, 02:41 PM

Opps! That would have to be 'ID'

Jeff Chambers · 01-23-2001, 03:34 PM

Actually, the size corresponds with the OD of hard tubing. -8AN is 1/2 inch tubing, whether its 0.035" wall, 0.065" wall or any other wall. With flex lines, it really doesn't correspond with anything other than a nominal hose/line size. A -8 braided hose has neither a .500" ID nor a .500" OD, but its OD is in the general neighborhood of 1/2 inch.

------------------
Jeff Chambers
Trophy Stock #3
11.97 Seconds / 114.5 MPH
Chambers Racing Team

Rev · 01-23-2001, 04:55 PM

This is amost informative thread. Thanks to all.

Rev

01-23-2001, 05:51 PM

The "dash" sizes are used in all types of hydraulic hose/fitting/tubing, like AN, JIC, SAE, pipe thread, etc.

Now, can anyone tell me what degree the taper is on the nose or seat of the fitting? I'm not sure if AN is the same as JIC which is 37 degrees or SAE which is 45 degrees. The threads are the same for both.

------------------
91 coupe
3.73's,long tubes,2 1/2" exh,ported stock t-body,ProM-77mm
cobra intake,edelbrock heads,B303,1.72 rr's
36lb inj's,tremec, & a Paxton NOVI 2000!!!
11.020 @128.95 on BFG Drag Radials (275/60/15)

[This message has been edited by SisuStang (edited 01-24-2001).]

Mach 1 · 01-24-2001, 02:03 AM

AN is 37 degrees.

------------------
1993 GT/AOD
'93 Mustang GT

FoxBuilder · 01-24-2001, 07:34 AM

Thanks for the correction Jeff.

dherrer1 · 01-24-2001, 11:12 AM

To all who have contributed to this tread. THANK YOU!!!! I received a very complete education. This really shows the power of this site!!

01-24-2001, 05:38 PM

Thanks Mach 1, you just made my day!

I have lots of JIC stuff around here at work, & it looks like AN is the same as JIC!!!!

Mach 1 · 01-24-2001, 07:47 PM

Your welcome, glad to help.

01-23-2001, 11:26 AM	#1 (permalink)
dherrer1 Registered Member Join Date: Jul 1999 Location: Carlsbad, CA Posts: 17	AN fittings Can someone explain to me the numbering scheme for AN fittings. What does a 6 AN mean? 6 millimetes ID or OD or what.... Thanks

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Grease Question	Kisner	Classic Mustangs	9	03-16-2004 07:47 PM
creaking noise!! AHH!	89GTimporteater	Windsor Power	4	03-20-2003 06:49 PM
What fittings will i need?	mustangLX92	Windsor Power	0	07-02-2002 08:33 AM
Teflon tape with nitrous fittings	Radon	Windsor Power	4	04-05-2002 01:04 AM
Oil Leak from S-Trim fittings...HELP	quick89gt	Windsor Power	0	08-03-2001 04:44 PM

01-23-2001, 12:27 PM	#2 (permalink)
FoxBuilder Registered Member Join Date: Sep 1999 Location: Columbus, Ohio Posts: 233	AN (Army-Navy) number simply stands for 16 ths of an inch, so -08 = 8/16" which = 1/2" ------------------ 1984 Mustang Top Fueler with Flowmaster's

01-23-2001, 02:41 PM	#4 (permalink)
FoxBuilder Registered Member Join Date: Sep 1999 Location: Columbus, Ohio Posts: 233	Opps! That would have to be 'ID'

01-23-2001, 03:34 PM	#5 (permalink)
Jeff Chambers Moderator Join Date: Aug 2000 Location: Milan, OH Posts: 2,699	Actually, the size corresponds with the OD of hard tubing. -8AN is 1/2 inch tubing, whether its 0.035" wall, 0.065" wall or any other wall. With flex lines, it really doesn't correspond with anything other than a nominal hose/line size. A -8 braided hose has neither a .500" ID nor a .500" OD, but its OD is in the general neighborhood of 1/2 inch. ------------------ Jeff Chambers Trophy Stock #3 11.97 Seconds / 114.5 MPH Chambers Racing Team

01-23-2001, 04:55 PM	#6 (permalink)
Rev Registered Member Join Date: Nov 1998 Location: Houston, Tx. Posts: 3,887	This is amost informative thread. Thanks to all. Rev

01-23-2001, 05:51 PM	#7 (permalink)
SisuStang Posts: n/a	The "dash" sizes are used in all types of hydraulic hose/fitting/tubing, like AN, JIC, SAE, pipe thread, etc. Now, can anyone tell me what degree the taper is on the nose or seat of the fitting? I'm not sure if AN is the same as JIC which is 37 degrees or SAE which is 45 degrees. The threads are the same for both. ------------------ 91 coupe 3.73's,long tubes,2 1/2" exh,ported stock t-body,ProM-77mm cobra intake,edelbrock heads,B303,1.72 rr's 36lb inj's,tremec, & a Paxton NOVI 2000!!! 11.020 @128.95 on BFG Drag Radials (275/60/15) [This message has been edited by SisuStang (edited 01-24-2001).]

01-24-2001, 02:03 AM	#8 (permalink)
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,864	AN is 37 degrees. ------------------ 1993 GT/AOD '93 Mustang GT

01-24-2001, 07:34 AM	#9 (permalink)
FoxBuilder Registered Member Join Date: Sep 1999 Location: Columbus, Ohio Posts: 233	Thanks for the correction Jeff.

01-24-2001, 11:12 AM	#10 (permalink)
dherrer1 Registered Member Join Date: Jul 1999 Location: Carlsbad, CA Posts: 17	To all who have contributed to this tread. THANK YOU!!!! I received a very complete education. This really shows the power of this site!!

01-24-2001, 05:38 PM	#11 (permalink)
SisuStang Posts: n/a	Thanks Mach 1, you just made my day! I have lots of JIC stuff around here at work, & it looks like AN is the same as JIC!!!!

01-24-2001, 07:47 PM	#12 (permalink)
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,864	Your welcome, glad to help.

Sponsored Links