wheel studs

maiden_deth · 06-28-2005, 11:50 PM

i recently bought a pair of draglites 15X8 with 5 1/2 in. backspacing for the rear.

i went to test fit them and the studs where too short to put them on

. i was wondering if you guy have any suggestions on who makes studs that would be long enough.

83GTMUSTANG · 06-29-2005, 12:22 AM

Go Get Some Mag Wheel Lug Nuts An Washers An Keep Your Stock Wheel Studs Or Order Some 3 In. Studs An Mag Wheel Lug Nuts From Summit Or Jegs..........

06-29-2005, 11:23 AM

Moroso makes a 3" race stud. Perfect for the Weld wheels.

ols0051 · 07-06-2005, 10:08 AM

I'm sure you have the correct lug nuts that thread into the gap between the rim and the stud right. On both my cars the studs don't expose them selfs on the outside of the rim, but with the supplied lugnuts they fit perfect.

06-28-2005, 11:50 PM	#1
maiden_deth Registered Member Join Date: Mar 2005 Posts: 22	wheel studs i recently bought a pair of draglites 15X8 with 5 1/2 in. backspacing for the rear. i went to test fit them and the studs where too short to put them on . i was wondering if you guy have any suggestions on who makes studs that would be long enough. __________________ 90 5.0 GT BBK full legnth headers BBK h-pipe Borla mufflers to dump off Auburn 28 spline rear diff. K&N conical filter C&L 76mm elbow BBK 75mm throttle body MSD distributer Edelbrock performer RPM II 3.73 gears

06-29-2005, 12:22 AM	#2
83GTMUSTANG N-V-ME Join Date: May 2005 Location: SOUTHFIELD,MICHIGAN Posts: 155	Re: wheel studs Go Get Some Mag Wheel Lug Nuts An Washers An Keep Your Stock Wheel Studs Or Order Some 3 In. Studs An Mag Wheel Lug Nuts From Summit Or Jegs.......... __________________ 88' LX MUSTANG: LINCOLN ROTORS , AIR SUSPENSION FRONT AND REAR, SUBFRAMES, ROLL CAGE, 92' BLOCK, MSD 6AL, ACCEL 8.8 WIRES, ACCEL COIL, EDELBROCK F4B INTAKE (PORTED),2 IN. 4 HOLE SPACERS, HOLLEY 600 CARB.,HOLLEY BLUE FUEL PUMP AN REGULATOR, E 303 (.498 IN. 220 DUR.) CAM, (.535 IN. OF LIFT W/ 1.72 SCORPIN ROLLER ROCKERS), PORTED E7'S, FLOWTECH 1 5/8 LONG TUBE HEADERS, 2 1/2 IN. H PIPE, 2 CHAMBER FLOWMASTERS WITH 3 IN.DUMPS, T-5, 3.73 GEARS, 5 LUG AEROSTAR AXELS, 245-45-17 96' COBRA WHEELS

06-29-2005, 11:23 AM	#3
Simi Stang Guest Posts: n/a	Re: wheel studs Moroso makes a 3" race stud. Perfect for the Weld wheels.

07-06-2005, 10:08 AM	#4
ols0051 Registered Member Join Date: Sep 2002 Location: cent.wis Posts: 203	Re: wheel studs I'm sure you have the correct lug nuts that thread into the gap between the rim and the stud right. On both my cars the studs don't expose them selfs on the outside of the rim, but with the supplied lugnuts they fit perfect.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
wheel studs	Lightspeed	Classic Mustangs	3	12-26-2002 01:59 PM
Wheel Studs Installation	glxstang	Windsor Power	3	03-27-2002 08:13 AM
wheel studs are evil	father joe	Blue Oval Lounge	1	02-27-2002 10:18 PM
Broken Wheel Studs...	AutoX281	Modular Madness	5	03-26-2001 03:00 PM
Wheel studs	MikeBlackGT	Windsor Power	1	02-10-2001 01:01 PM