![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Jun 2002
Location: phoenix, az
Posts: 20
|
![]() finally got everything put together, oil prepped the rebuilt motor, put gas in the tank, charged the battery and all I needed to do was drop in the distributor before cranking it up after 11 months in the garage. but... just added Aeromotive fuel rails and there is no way in hell that the distributor is going to be forced into place with those things digging into it let alone move at all to adjust timing. similar problems? solutions? advice?
__________________
88 Conv Vortech S-trim 2.5" 10-rib pulley, 332 stroker w/ Cat forged crank, forged JE flat-tops, forged rods, 10.25:1 comp, DSS girdle, edelbrock heads, Omega valvetrain, Lunati custom cam, extrude honed Cobra intake, 70mm T-body, Pro-M 77, bypass valve, dual Walbro 255 lph in tank pumps, an -8 fuel hose, aeromotive fuel rails/regulater. 42# inj, MSD ingniton/boost retard, JBA headers, flowmasters, full Griggs GR-40R suspension (K-member, torque arm, panhard bar, subframes, strut brace) Centerforce clutch, Tremec, Auburn posi locker, moser axles, Baer brakes/rotors, 17" cobra R wheels, custom body/roll bar |
![]() |
![]() |
![]() |
#2 |
gear banger
Join Date: Aug 2000
Location: CHICAGO
Posts: 1,144
|
![]() Did you use the spacers for the drivers side rail? You need them.
Do you have any -AN fittings on the front of the drivers side rail? If so find another way to to install the fuel lines, it will not fit unless you notch the distrubuter. Wade
__________________
79 Hatch: NA 347, Stage 2 Canfield Heads, Victor JR. Intake, Blueprinted Holley 750 HP, Solid Roller Cam, Shooting for 10's on motor 93 LX: Tremec, dual friction clutch, fms flywheel, Hedman shorties, O/R H-pipe Ricer hater's club member #49 |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2002
Location: phoenix, az
Posts: 20
|
![]() yea, i used the spacers on the drivers side rail and i have it plugged with the plug that came with the rail, but its still not fitting in. i even took out the screws to move the rail out farther, but the injectors are at enough of an angle to leak going into the intake.
__________________
88 Conv Vortech S-trim 2.5" 10-rib pulley, 332 stroker w/ Cat forged crank, forged JE flat-tops, forged rods, 10.25:1 comp, DSS girdle, edelbrock heads, Omega valvetrain, Lunati custom cam, extrude honed Cobra intake, 70mm T-body, Pro-M 77, bypass valve, dual Walbro 255 lph in tank pumps, an -8 fuel hose, aeromotive fuel rails/regulater. 42# inj, MSD ingniton/boost retard, JBA headers, flowmasters, full Griggs GR-40R suspension (K-member, torque arm, panhard bar, subframes, strut brace) Centerforce clutch, Tremec, Auburn posi locker, moser axles, Baer brakes/rotors, 17" cobra R wheels, custom body/roll bar |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
fuel pressure issues | mustang98gt | Modular Madness | 3 | 07-05-2003 10:43 PM |
98GT fuel rail modification | elhombre | Stang Stories | 0 | 10-15-2002 09:50 PM |
Anyone ever busted a fuel rail? | Rebel79 | Windsor Power | 0 | 08-01-2002 03:15 PM |
Oh No Fuel leak on driver's side rail...Can I use teflon tape????? | Stang_ROTY | Windsor Power | 2 | 08-05-2001 09:16 AM |
Fuel rail question | leo | Windsor Power | 1 | 07-18-2001 01:22 PM |