![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Jul 2002
Location: Scotrun, PA
Posts: 4
|
![]() Hey, i'm trying to replace my grommet but I can't seem to figure how to get the new one on or the old one off(well i could cut it off but i wanna do it the right way). How should I go about replacing this? This is for my 95 gt convertible if that makes a difference. Thanks a lot.
__________________
-1995 Mustang GT Convertible -1970 Dodge Challenger(440ci) |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 2002
Location: Kingston, Ontario
Posts: 351
|
![]() I'm not sure about a 95 but on my 88 I'm pretty sure you have to drop the tank
I had the tank out and put it back in and after that the grommet started leaking and I dropped the tank again to change it, couldn't figure any other way to do it Hope there is an easier way but I wouldn't count on it
__________________
![]() '88 lx, Black on Black, check it out here Spent all my money on school, what a dumb mistake I'm old enough to know better, but still too young to care. |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Feb 2002
Location: Jacksonville, FL
Posts: 706
|
![]() Yeah, I have to agree. The easiest way to tackle that one is to drop the tank. It's only the 2 retaining strap bolts. Just make sure you get as much gas out of it that you can. Otherwise it becomes difficult to handle.
Good Luck.
__________________
1988 GT Convertible 331 10:1 TW heads, GT-40 intake, MSD, TRW flattops, B Cam w/ 1.7's, MAC exhaust, 24's, 70 TB, 76 MAF, 3.73's, Pro 5.0, Koni's, Anderson PMS, Wideband 02, yatta, yatta... One week with new motor, two speeding tickets...joy |
![]() |
![]() |
![]() |
#4 |
Mizzou Tigers
Join Date: Apr 1999
Location: weston, MO United States
Posts: 1,455
|
![]() Yup, I just replaced mine last week. Drop the tank and the filler neck just slides in and out. Pop out the old grommet and put in the new one. Btw, I used a floor jack under the tank to help lower and raise it back into place. It works really well....I have even dropped the tank before by myself using this method.
__________________
2006 Mustang GT 1990 LX GT-40 motor 262 horsepower, 307ft-lbs (sold but forever loved) 1998 Contour SVT Rice Haters Club Member #244 |
![]() |
![]() |
![]() |
#5 |
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
![]() I cheated...
Mine was leaking on left-handers, and I got black flagged (must pull into pits) when I was at the track. I simply used and ENTIRE tube of RTV around the gasket, and voila! ![]()
__________________
Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Apr 2002
Location: Kingston, Ontario
Posts: 351
|
![]() it's funny some of the **** you can come up with when black flagged in the middle of a race. Just rig it up and get back out there!
__________________
![]() '88 lx, Black on Black, check it out here Spent all my money on school, what a dumb mistake I'm old enough to know better, but still too young to care. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Safety Issue 64 - 70 Mustangs | Mach1 Cobra Jet | Classic Mustangs | 20 | 07-11-2005 08:06 PM |
Pressure build up in Gas Tank | Fuglee | Windsor Power | 1 | 08-21-2003 02:22 PM |
Tranny filler tube? | mystang_71 | Classic Mustangs | 2 | 07-10-2003 03:25 PM |
Pulling vacaum through oil filler tube. | Mopar1 | Windsor Power | 18 | 09-18-2002 07:35 PM |
Fuel Tank Question | RMARIANI | Windsor Power | 3 | 10-15-2001 03:29 PM |