![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Sep 2000
Location: New Hope MN USA
Posts: 276
|
![]() Well as I mentioned an another post I am finally putting my heads in and I was wondering if there is anything else I should replace besides the gaskets, etc. While I have everything off. Thanks in advance....
------------------ 91 LX Convertible Gray on Red B&M Shift improver kit,ASP red alum. underdrive pulleys, Richmond 3.73 gears, 1 5/8 Flowtech long tube Headers and off road h-pipe, Flowmaster 2-chamber cat-back with S.S exhaust, MSD 6A Ignition with coil,Cap and rotor, Taylor Pro wires, K&N 12" conical filter system, Jet stage 2 performance chip,GT40 P heads, looking at new exhaust, Lentech Street Terminator plus. |
![]() |
![]() |
![]() |
#2 |
Backyard Mechanic/Chemist
Join Date: Feb 2001
Location: Acton MA USA
Posts: 435
|
![]() Many recomend new head bolts every time the heads are removed. Probably good advice with lots of other add-on's etc. Also a real good time to consider a new intake since it will be removed during the swap. You could also swap a new cam in with not much more work.
------------------ Frank W 90 5.0 LX coupe Daily driver. Silencer removed, K&N filter. Flexalite fan, 3 core radiator. FMS flywheel and Clutch, FMS blue wires Energy Suspension end links 88 Notch 2.3L 5 speed Parts/beater car My two Notchbacks 74 Chevy Laguna Type S-3 305 Finally fixed getting a 454 to put in garage <A HREF="http://www.chevellepages.com/folingo" TARGET=_blank>www.chevellepages. |
![]() |
![]() |
![]() |
#3 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() If your motor has very many miles on it and still on the same double roller chain..i would replace it.
------------------ 347 Stroker Motor: Balanced, Cobra Transmission, Extrude Ported and Polished Upper and ported Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, 30lb Bosch Injectors, Holley Fuel Regulator, March Underdrive Pulleys, Perma-Cool Fan, 3-Core Radiator, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 79mm Mass Air Unit, 70mm TB, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Short Throw Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, AC del |
![]() |
![]() |
![]() |
#4 |
Tubbed and Juiced
Join Date: Mar 2001
Location: Tulsa, Oklahoma
Posts: 1,861
|
![]() Stock head bolts on a stang can only be used once. Once you remove them from the stock heads they are toast. Get some ARP head bolts, it will be well worth it.
------------------ 3:55's,BBK Off-Road H-pipe,BBK jet-hot coated equal length shorty headers,BBK 70mm Throttle Body,BBK adjustable clutch quadrant,C & L 76mm Mass air meter,Cobra R's 17x9 w/ 245's,Trick Flow Intake,Flowmaster Force II exhaust system, Super Duty T5,Centerforce II Clutch,Heavy Duty Radiator,9mm Ford racing plug wires,Accel cap and Rotor www.geocities.com/i8urvpr/JM.html?987369348700 |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Apr 2000
Location: middleburg, fl, usa
Posts: 1,134
|
![]() The stock head bolts are called torque to yield bolts, and while I have no idea what that means they can only be used once. If you use them again, you will not have the correct ft. lbs. and could cause gasket failure.
------------------ James Cox nochevy@hotmail.com 1991 Mustang LX 12.565 @109.38mph 1.764 60ft |
![]() |
![]() |
![]() |
#6 |
Backyard Mechanic/Chemist
Join Date: Feb 2001
Location: Acton MA USA
Posts: 435
|
![]() oooh 5.0's use the torque to yeild bolts, I was unaware of that newer GM engines use them too. Obviously those have to be replaced as they stretch during installation. Even regular head bolts are recomended to be replaced for higher Hp engines. I re-used the head bolts twice in my mild 305 which pumps out 275 hp or so.
------------------ Frank W 90 5.0 LX coupe Daily driver. Silencer removed, K&N filter. Flexalite fan, 3 core radiator. FMS flywheel and Clutch, FMS blue wires Energy Suspension end links 88 Notch 2.3L 5 speed Parts/beater car My two Notchbacks 74 Chevy Laguna Type S-3 305 Finally fixed getting a 454 to put in garage <A HREF="http://www.chevellepages.com/folingo" TARGET=_blank>www.chevellepages. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Head Swap finally Done | Badass_yellowGT | Modular Madness | 3 | 11-14-2002 02:34 AM |
Head swap question | Badass_yellowGT | Modular Madness | 11 | 11-04-2002 11:19 PM |
Thinking of 99 head swap? BEWARE... | 97ScottieGT | Modular Madness | 7 | 03-14-2002 01:43 PM |
those with '96-98 motors and want a head swap. | Ares | Modular Madness | 6 | 01-18-2002 10:30 AM |
97GT head swap | speedemon | Modular Madness | 6 | 11-04-2001 06:56 PM |