H-pipe, headers, exhaust with 93 cobra

Sonics2042 · 02-03-2002, 04:55 PM

Hello,

I am looking to get all of these for when I get my Cobra. My question is if all 87-93 exhaust parts are fully interchangable with the 93 cobra? I heard that a 87-93 exhaust is about 2 inches too short for the cobra.

Basically, I found prices for the h-pipe, headers, exhaust for a 87-93 mustang and I need to know if there are any special considerations I should make.....since it is a cobra.

Thanks,
DoranW

Unit 5302 · 02-03-2002, 05:18 PM

Bassani. Go with the long tube setup. SaleenGTS was dynoing at 315hp at the crank with an exhuast, and not much else if I remember right.

93 Cobra needs input · 02-03-2002, 09:16 PM

No problems with the 87-93 parts I have a 93 Cobra and installed BBK long tube ceramic headers bolted right in perfect fit never had to loosen the engine mounts. Nice fit lots of power hope this helped any other questions just e-mail me I would be happy to answer any questions.

02-03-2002, 04:55 PM	#1
Sonics2042 Registered Member Join Date: Jul 2001 Location: Seattle, WA Posts: 381	H-pipe, headers, exhaust with 93 cobra Hello, I am looking to get all of these for when I get my Cobra. My question is if all 87-93 exhaust parts are fully interchangable with the 93 cobra? I heard that a 87-93 exhaust is about 2 inches too short for the cobra. Basically, I found prices for the h-pipe, headers, exhaust for a 87-93 mustang and I need to know if there are any special considerations I should make.....since it is a cobra. Thanks, DoranW __________________ What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Speed Secret # 3	jim_howard_pdx	Windsor Power	13	11-09-2002 10:35 AM
H pipe with JBA full length headers	bobtodd	Windsor Power	1	05-30-2002 10:03 AM
What should I pay for a low mileage used Cobra Exhaust?	MonsterTrosity	Blue Oval Lounge	4	10-22-2001 11:44 AM
96 Cobra Exhaust Question	mosibobo	Modular Madness	4	03-21-2000 06:32 PM
Cobra Headers	97snakedriver	Modular Madness	2	01-17-2000 05:14 PM

02-03-2002, 05:18 PM	#2
Unit 5302 Registered Member Join Date: May 1999 Posts: 5,246	Bassani. Go with the long tube setup. SaleenGTS was dynoing at 315hp at the crank with an exhuast, and not much else if I remember right.

02-03-2002, 09:16 PM	#3
93 Cobra needs input Registered Member Join Date: Oct 2001 Location: Madelia,MN USA Posts: 58	No problems with the 87-93 parts I have a 93 Cobra and installed BBK long tube ceramic headers bolted right in perfect fit never had to loosen the engine mounts. Nice fit lots of power hope this helped any other questions just e-mail me I would be happy to answer any questions.