how do you clean connections

cjm · 01-04-2001, 08:51 AM

I'm using a used harness & computer for an engine swap that I'm doing. Have read about the problems caused by bad connections. What is the best way to clean the connections? should I use a dielectric grease on the connections?

01-04-2001, 11:28 AM

Go to your auto parts store and they should have something called electrical parts cleaner. Spray it on there, then use compressed air to blow it out. Now just put some dielectric grease on the pins, or in the female end and connect it.

cjm · 01-04-2001, 12:24 PM

Will it be ok to spray the cleaner in the computer connections?

LX XLR8R · 01-05-2001, 03:06 PM

yes i highly recremend using dielctric grease on all ur connnections and spark plug wires..it will save ur connections in the long run(corrosion), and keep mosture out, while keeping the connections from getting stuck 2gether

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

01-04-2001, 08:51 AM	#1 (permalink)
cjm Registered Member Join Date: Dec 2000 Location: tuscumbia, Al. Posts: 17	how do you clean connections I'm using a used harness & computer for an engine swap that I'm doing. Have read about the problems caused by bad connections. What is the best way to clean the connections? should I use a dielectric grease on the connections?

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Clean your K&N!	ac97gt	Modular Madness	5	08-29-2004 10:50 PM
clean engine bay!!	pedley	Windsor Power	0	01-03-2004 06:37 PM
Can you CLEAN O2's	drtbiker	Windsor Power	4	10-15-2002 09:06 PM
Miracle clean for inside of polished Aluminum rims!!	Fox Body	Appearance & Detailing	2	03-08-2001 06:42 PM

01-04-2001, 11:28 AM	#2 (permalink)
88GT5.013.02 Posts: n/a	Go to your auto parts store and they should have something called electrical parts cleaner. Spray it on there, then use compressed air to blow it out. Now just put some dielectric grease on the pins, or in the female end and connect it.

01-04-2001, 12:24 PM	#3 (permalink)
cjm Registered Member Join Date: Dec 2000 Location: tuscumbia, Al. Posts: 17	Will it be ok to spray the cleaner in the computer connections?

01-05-2001, 03:06 PM	#4 (permalink)
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	yes i highly recremend using dielctric grease on all ur connnections and spark plug wires..it will save ur connections in the long run(corrosion), and keep mosture out, while keeping the connections from getting stuck 2gether ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

Sponsored Links