MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 03-16-2009, 12:00 AM   #1
89LX boosted cobra
89LX soon 13psi
 
Join Date: Mar 2009
Location: ga
Posts: 16
Default HP estimate and ET's

i have an 89LX. fresh motor with about 20k on it. bored .30 over with 30 over pistons. heads were reworked but not ported. i have a powerdyne supercharger bd-11a with a 9lb pulley, but only see 6 lbs on the gauge, 73mm mass air meter, bbk shorty headers, off road x pipe, 2 chamber flowmasters, bassani tail pipes, 190lph fuel pump, king cobra clutch kit, pro 5.0 shifter, ford racing starter, aluminum radiator, full length frame connectors, strut tower brace, caster cambers, eibach sportline springs, kyb gr2 struts, sn-95 brakes, with cobras up front, 99 cobra wheels with 245/45/17 tires. everything else is pretty much still stock, intake, tb, etc. with stock 3.08 gears. what would be my est HP and ET before and after smaller pulley to get to 9lbs of boost, and 3.55 ford racing gears?
89LX boosted cobra is offline   Reply With Quote
Old 03-17-2009, 10:56 PM   #2
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: HP estimate and ET's

well i wouldnt expect too much with the mostly stock engine,yea you have boost but u have to move all that air and feed it fuel.with 6psi and stock gears i would say like 13.3 in the 1/4 mile.if u up the boost and i would go with 373 mabey 12.8.but thats if u have tires that hook..i wouldnt go with 355 the 373 will help ur 60ft a little more.if you had cam intake heads bigger t-body bigger fuel pump bigger injectors and a good tune then u would be really talking about some 11sec time slips..goodluck dude
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 03-19-2009, 06:18 PM   #3
89LX boosted cobra
89LX soon 13psi
 
Join Date: Mar 2009
Location: ga
Posts: 16
Default Re: HP estimate and ET's

thanks for the advise. really trying to stay as a decent cruising car with moderate power, brakes, interior, and suspension. but still be a good competitor. decided to not go the all out drag car etc. i also know i will eventually go with more power is the reason for the 3.55's considering all the torque the car produces. i'm eventually going with a good set of gt40's, or maybe work in a set of afr's. E303 cam, gt40 intake, and maybe a little spray. thanks for all the data!!!
89LX boosted cobra is offline   Reply With Quote
Old 04-16-2009, 10:51 AM   #4
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: HP estimate and ET's

Be sure to put a T-rex in addition to your 190lph or second inline fuel pump on that car if you are going to stay with boost. You will run lean without it.
__________________
USMC302 is offline   Reply With Quote
Old 04-16-2009, 12:19 PM   #5
89LX boosted cobra
89LX soon 13psi
 
Join Date: Mar 2009
Location: ga
Posts: 16
Default Re: HP estimate and ET's

ok, thanks. i also have another problem. my car unannounced, will start to surge when idling. sometimes it idles great then just start to surge, then usually straiten back out. i noticed when i had the supercharger belt off, the car idled great and never serged. any ideas?
89LX boosted cobra is offline   Reply With Quote
Old 04-17-2009, 10:06 AM   #6
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: HP estimate and ET's

make sure the throttle body is clean, with the new boost, it's been sucking more air than usual, make sure all components are clean, including the air filter for the S/C
__________________
USMC302 is offline   Reply With Quote
Old 12-16-2009, 08:46 AM   #7
suprchrg'dstang
Registered Member
 
suprchrg'dstang's Avatar
 
Join Date: Nov 2001
Location: minnesota
Posts: 9
Default Re: HP estimate and ET's

Sounds like a maf problem to me... 73 mm C&L? try clocking the maf to a different position. Also get a tune and some bigger injectors.
I was making ~5lb of boost with my SN2000 blower. And with stock everything cept TFS intake and full exhaust. And 42lbs injectors
I made 300rwhp 350rwtrq.

I'd guess you are around there too
suprchrg'dstang is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
ET's fiveOguy20 Windsor Power 2 01-22-2003 09:23 PM
2nd ET's with new motor fiveOguy20 Stang Stories 7 10-14-2002 07:35 AM
1st ET's with new engine fiveOguy20 Windsor Power 7 09-28-2002 07:11 PM
01 GT ET's DOMIN8R97 Modular Madness 2 09-25-2001 02:13 PM
Fastest 1/4 ET's poopstang Windsor Power 9 05-22-2001 07:59 AM


All times are GMT -5. The time now is 02:51 PM.


SEARCH