Need some AN fitting help...

Rick 91GT · 02-18-2001, 11:07 PM

Can anybody compare the AN fitting sizes to a standard or metric measurement. EXAMPLE AN -6 = 3/8" or 9.5mm etc..

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

Mach 1 · 02-19-2001, 07:45 AM

The AN number refers to the diameter of the hose/tubing. It is in 16ths of an inch. AN-6 is 6/16th, 8 is 8/16ths, AN4 = 1/4 inch, etc...

I like your site and your car, but whats up with the "pro - 5.0" on your shield? Thinking of going up against the big boys..lol!

[This message has been edited by Mach 1 (edited 02-19-2001).]

Rick 91GT · 02-19-2001, 08:53 AM

I wish I could run with the big boys

After the local cops busted me for having "Steeda" across the windsheild ( they said it hinderd my view even though it was above the A line) I had the Pro 5.0 hanging around from my shifter, every time I saw the owner of Pro 5.0 he gave me banners and T-shirts for giving him feed back on his shifter, it looked weird not having anything so I slapped it on. Now it has my own banner "RNH PERFORMANCE RACING" I'll get some new pics after the roll bar install and other winter goodies.

Thanks,

Rick

------------------
My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

02-18-2001, 11:07 PM	#1
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Need some AN fitting help... Can anybody compare the AN fitting sizes to a standard or metric measurement. *EXAMPLE AN -6 = 3/8" or 9.5mm etc..* ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Fuel Line fitting	289	Windsor Power	2	08-27-2004 01:50 PM
CAI bastard fitting? Help!!	Tripleduece	Windsor Power	5	07-16-2004 02:10 PM
Heater hose fitting w/ECT mount ???	Chris in NY	Windsor Power	2	05-30-2003 04:34 PM
Q about Pedistal Rockers fitting after Decking	Chipdog	Windsor Power	1	10-01-2002 01:35 AM
O2 Sensor Fitting	Jeff7477	Windsor Power	4	07-30-2001 12:50 PM

02-19-2001, 07:45 AM	#2
Mach 1 Registered Member Join Date: May 1999 Location: Georgia Posts: 3,866	The AN number refers to the diameter of the hose/tubing. It is in 16ths of an inch. AN-6 is 6/16th, 8 is 8/16ths, AN4 = 1/4 inch, etc... I like your site and your car, but whats up with the "pro - 5.0" on your shield? Thinking of going up against the big boys..lol! [This message has been edited by Mach 1 (edited 02-19-2001).]

02-19-2001, 08:53 AM	#3
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	I wish I could run with the big boys After the local cops busted me for having "Steeda" across the windsheild ( they said it hinderd my view even though it was above the A line) I had the Pro 5.0 hanging around from my shifter, every time I saw the owner of Pro 5.0 he gave me banners and T-shirts for giving him feed back on his shifter, it looked weird not having anything so I slapped it on. Now it has my own banner "RNH PERFORMANCE RACING" I'll get some new pics after the roll bar install and other winter goodies. Thanks, Rick ------------------ My Ride Check Out My Site 91GT, Holley SysteMAX II Kit-Heads 2.02" x 1.60",Full MAC exhaust 1-5/8" Long tubes, 2-1/2" O.R H-Pipe, 2 1/2" cat back, 12" K&N Filter, RNH PERFORMANCE Ram Air, Ron Davis Radiator, Full Suspension,3:73's, Welds, Best on new motor-12.60 @ 108, no traction 1.98