MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar Mark Forums Read

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 11-30-2007, 11:45 PM   #1
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default knocking mustang 5.0

i have an 89 coupe and just installed a new set of gt40 heads, e303 cam, and 1.7 crane rockers. when starting the car up for the first time there was a loud knocking noise. i thought the valves hit the piston since it was pretty loud, but the numbers show plenty of room for this combo. anyhow, i took one head off and found that everything looks fine and that there are no signs of the valves hitting. i put everything back together and still get a knocking. other mods are c&l 76 mm maf, bbk 70 mm tb, tf track heat upper and lower, and heads are port matched on both the intake and exhaust. i bought spark plugs based on a '93 cobra. even when i retard the timing it doesn't seem to have a possitive effect. any ideas?
5150coupe is offline   Reply With Quote
Old 12-01-2007, 09:12 AM   #2
DaLe five OH!
Registered Member
 
Join Date: Nov 2006
Location: Naples FL
Posts: 106
Default Re: knocking mustang 5.0

bent push rod? bad rocker? loose rocker? bent valve?
__________________
ZEX
DaLe five OH! is offline   Reply With Quote
Old 12-01-2007, 11:57 AM   #3
Dark_5.0
Registered Member
 
Dark_5.0's Avatar
 
Join Date: Apr 2001
Location: Staging lane
Posts: 4,337
Default Re: knocking mustang 5.0

Take off all of the rockers and pushrods and inspect eveything. Look for bent pushrods or damaged rockers. The rockers are pedistal mount right???
__________________
92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim.
00' Lightning-Stock
88'CRX-13 second ego killer
Dark_5.0 is offline   Reply With Quote
Old 12-07-2007, 09:47 PM   #4
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

i ended up finding out that it was just a timing issue. just backfiring...but now i have a couple other related issues. i can't seem to set the timing to 14 like it was before. at 14 i get backfiring and it won't idle or run well unless it is advance way to high at about 22-25. it doesn't seem to ping even though it is high, so i thought maybe the timing marker is off or something, but it looks to be at the same location as my friends coupe. i'm going to put it on the computer and start checking codes.
5150coupe is offline   Reply With Quote
Old 12-11-2007, 12:00 PM   #5
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: knocking mustang 5.0

Sounds like you a tooth off. Pull the dist, set engine to TDC, and restab it. Double check your ignition wires as well to make sure you don't accidentally have one crossed.
__________________
USMC302 is offline   Reply With Quote
Old 12-11-2007, 10:37 PM   #6
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

13726548 firing order and i think u point the rotor to the ft drivers side upper intake bolt its like 1 oclock
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-11-2007, 10:39 PM   #7
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

dont forget thats at tdc
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-12-2007, 10:44 AM   #8
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: knocking mustang 5.0

Quote:
Originally Posted by goodyear1984 View Post
13726548 firing order and i think u point the rotor to the ft drivers side upper intake bolt its like 1 oclock
Negative. The rotor should point directly at the number 1 post on the dist, that's the one that's connected to cylinder number 1.
__________________
USMC302 is offline   Reply With Quote
Old 12-12-2007, 06:40 PM   #9
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

the only way the rotor wont hit the number one is if ur off a tooth ..not negitive look up the rotor position and set it there with the engine at tdc.then if u have the rotor set right get the rotor to be as close to number 1 as possiable so it will start up the first time. then set timing, and if u set the rotor and have it at tdc of compression stroke it will be perfect.
goodluck
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-12-2007, 06:50 PM   #10
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

also if u have the pedestal mount rockers make sure u check the valve lash most times u dont need to shim but u will get a back fire if u are in need of a shim.i had to shim only one of my rockers because of a backfire problem, and hopefully u have a good set of springs
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-13-2007, 06:09 PM   #11
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

-how do i know if it is on the compression stroke. what i have been doing is this: crank the motor till the damper is at 0 degrees and the 1 st piston is at the top. then i set the distributor pointer to the #1 post. it seems to start fine this way, but still won't run at 14 degrees or anything close. i will only run way past 14 degrees, but has no power and is hard to start. maybe the springs cause i left the stock gt40 springs on, but they are double coil and that seems fine for my conservative combo.
5150coupe is offline   Reply With Quote
Old 12-14-2007, 07:36 PM   #12
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

i guess it makes sense to just plug the spark plug hole with my thumb and crank till there is pressure...
5150coupe is offline   Reply With Quote
Old 12-14-2007, 07:37 PM   #13
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

take out the number 1 plug.thats the passenger side front.have someone bump it over with your finger over the plug hole when u feel a big amount of air come out thats the compression stroke not a little amount but a good amount and 0 degrees should be close to the pointer on the balancer.line the balancer to zero degrees...now the the rotor has to be set .dont just slap the dis in there so its pointed to the number 1 spark tower on the cap thats the wrong way.now if u have the motor set at tdc on the compression stroke set at 0degrees your good.if ur not sure u can take the pass side valve cover and make sure the front rockers are all the way up if not then ur off and do it again.ok now set the dis in u want the rotor facing the intake straight back.it wont be perfectly straight back and will close to pointing the ft driver side bolt for the upper intake.now that the rotor is set bolt on the dis clamp not to tight ,u still have to set timing but u dont want the dis to move much when u start the engine .now u can set the dis so the rotor is just under the number 1 spark tower on the cap.check to firing order 2 or three times and make sure u have the right firing order the 302 ho is 13726548 and that is in a counter-clockwise order on the cap.now start and set the timing.put it at 15 and rember that each line 2 degrees. do this to the T and it will be right.
goodluck
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-14-2007, 07:42 PM   #14
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

...that's right about the rotor needing to point to the #1 spark plug post. if the #1 post is pointing to the upper manifold bolt at 1 o'clock that is probably a good position to have enough room for timing adjustment, but really it doesn't matter as long as the rotor points to the # 1 post and you give the distributer enough room for movement.
5150coupe is offline   Reply With Quote
Old 12-15-2007, 02:21 AM   #15
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

i set everything as described, but still have the same issue. the only thing i could be doing wrong is maybe not getting the compression stroke, but i basically cranked the motor till i felt a surge of air and then set the timing marker to 0 degrees. all i get is a slight amount of backfiring. tomorrow i will remove the passenger side valve cover to make sure it is on the compression stroke by making sure the rockers are both at their lowest point.
5150coupe is offline   Reply With Quote
Old 12-15-2007, 10:25 PM   #16
5150coupe
Registered Member
 
Join Date: Jun 2007
Posts: 28
Default Re: knocking mustang 5.0

found out that the spring on the throttle body was off, which solves the recent starting issue...knew it would be something like that. so now it is running and i can drive it but still have to set the timing to about 26 degrees to have a good idle, easy start, and decent power. since i can now drive the car i'm going to take it to a friend who has been a mechanic for about 45 years and specializes in mustangs. hopefully we will get the timing issue worked out for good. i will keep updating...
5150coupe is offline   Reply With Quote
Old 12-17-2007, 01:59 AM   #17
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

thats prolly it u will get it
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 12-19-2007, 11:56 AM   #18
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: knocking mustang 5.0

Quote:
Originally Posted by goodyear1984 View Post
.dont just slap the dis in there so its pointed to the number 1 spark tower on the cap thats the wrong way.
What do you mean that's the wrong way?
__________________
USMC302 is offline   Reply With Quote
Old 12-23-2007, 01:23 PM   #19
goodyear1984
Registered Member
 
Join Date: Dec 2006
Location: new york
Posts: 482
Default Re: knocking mustang 5.0

because ths correct way is to set the rotor position between 12 and 1 o'clock at tdc and the set the dis cap so its on #1..if the shaft gear isnt meshed on the same spot on the cam drive gear from the factory, you will hit the water neck when ur trying to get the timing set
__________________
347 stroker all forged,arp everything,stud mains w/girdle,7qt pan,full roller, custom cam, aluminum heads swirl valves 5 angle valve job.quick fuel 750,areomotive pump,cobras w/nitto drags,and m/t et drags for the track, ford racing 373 gears,centerforce clutch,tko500,underdrive pulleys,bassani x-pipe,flowmasters
^best et so far 11.6 1.61 60ft coming soon 9sec et's
1992 mustang gt
2001 gmc 1500 4x4
78 century boat
92 skidoo
goodyear1984 is offline   Reply With Quote
Old 01-03-2008, 01:53 PM   #20
USMC302
Registered Member
 
USMC302's Avatar
 
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
Default Re: knocking mustang 5.0

I've never had a problem hitting the water neck before, but technically you could set the dist any way you want as long as the start the firing order is on number one and the wires follow suit on the cap. It might be different from what you do but definately not WRONG. Even Ford suggests to do it the way I've described, that's how I learned anyway some 13 years ago, hasn't failed me yet. Just actually got a car running for the first time after a rebuild for a buddy of mine, it had an engine fire and he picked it up for only $450. We have him advanced to 14 degrees and are not even close to the water neck....
__________________
USMC302 is offline   Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Knocking When My 00 Gt is Cold? Help Crackerballer Modular Madness 1 07-18-2002 09:06 PM
Bad knocking noise mustangLX92 Windsor Power 0 07-09-2002 07:54 AM
I can hear you knocking.... jerrys84 Windsor Power 0 04-22-2002 10:40 AM
ticking/knocking noney16 Windsor Power 3 04-04-2002 12:26 PM
Morning knocking Rocket 99GT Modular Madness 3 03-28-2001 03:08 PM


All times are GMT -5. The time now is 07:01 AM.


SEARCH