Mac headers coated with high temp baked on paint
 

before installing my headers i had them coated...a freind of mine works at a mufflers facotry where they paint exhaust then run it through a oven and its baked on..so here are my headers after words...
http://us.f1.yahoofs.com/users/57a53...fbNO7AXmcI3wYO

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Future Mods:3.73's,Pro 5.0,Shifter knob,E303 cam,cobra intake,65mm tb
ICQ#35670781

the main reason for doing it was one..i figured macs rust fast so mabe this would keep them from rusting so fast...and two..it was free..haha..and no the paint is NOT holding up to the heat..the paint close to where the headers bolt on is flaking off..but o well..it was free

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Future Mods:3.73's,Pro 5.0,Shifter knob,E303 cam,cobra intake,65mm tb
ICQ#35670781

here is a pic of what they looked like before i had them coated
http://us.f1.yahoofs.com/users/57a53...fbNO7A8RQTYI1E

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Future Mods:3.73's,Pro 5.0,Shifter knob,E303 cam,cobra intake,65mm tb
ICQ#35670781

i think some of you might have to right click the red "x" and go to properties and copy the link and paste it in a new browser window

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Aiwa deck,power acoustic amp,2 12" pianeers,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Future Mods:3.73's,Pro 5.0,Shifter knob,E303 cam,cobra intake,65mm tb
ICQ#35670781

I had my MAC long tubes Ceramic coated inside and out to prevent rusting and increase performace. Now my cat back got stained when the tranny let loose and it looked bad so I just repainted that with the Dupont 1200 degree hi-temp paint, it looks really nice.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!

I should have pulled my headers out when I did all my work and had them ceramic coated because they really make the engine compartment look worse with all the rust spots on them. I'm going to have to do that when I swap engines I guess.

------------------
Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph

Indiana Stangers Association
Buy your parts here
ICQ# 42269241