MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Windsor Power
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 06-13-2001, 11:22 AM   #1
DemonGT
Registered Member
 
DemonGT's Avatar
 
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
Post new intake install, MAJOR PROBLUMS!!!!(long)

well...installed my TFS intake and accufabe TB..started the car and had a bad vacum leak..found that and fixed it..put antifreeze back in..idled fine in the garage..then when i backed it out and hit the brakes they were stiff as hell...had to push as hard as i could to stop...then when i went down the block it suddenly started bucking then made a few odd noises and stalled???? WTF

my freind that helps me said he thinks we forgot a vaccum line and that, that vaccum line sucks oil to the top of the motor..and that when it stalled it ran out of oil on the top end and bent my push rods??? need some help bad!!!



------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Waiting install:TFS street heat,Accufab TB

Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's
ICQ#35670781
DemonGT is offline   Reply With Quote
Old 06-13-2001, 11:30 AM   #2
93CobraR
Registered Member
 
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
Post

Sounds like a vaccume like to me too. Check the big vac. line that comes off the firewall onthe drivers side. It's a a tree with a few others. As for bending the pushrods and running out of oil?? I don't think so. Oil doesn't flow threw the intake.

------------------
87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's.
Best time 12.759
Best MPH 106.79
Best 60' 1.695

Visit my site at:
http://www.geocities.com/cobrar93_2000/MyPage.html

93CobraR is offline   Reply With Quote
Old 06-13-2001, 11:51 AM   #3
DemonGT
Registered Member
 
DemonGT's Avatar
 
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
Post

also..when it started bucking and jerking it was like it was being starved for either gas or air..and once it stalled some smoked was coming out from the hook..dont know if it was smoke or steam or what...

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Waiting install:TFS street heat,Accufab TB

Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's
ICQ#35670781
DemonGT is offline   Reply With Quote
Old 06-13-2001, 12:21 PM   #4
2FastLX
The Photoshop Guru
 
2FastLX's Avatar
 
Join Date: Feb 2001
Location: Mecca, Indiana
Posts: 1,419
Post

What color was the smoke? Could it be an intake leak? Spray some WD-40 around your intake and see if the idle changes. If so you are leaking. Go to Auto Zone and get a vacuum tester - $20. Test the vacuum to see if you have at least 15 inches.

------------------
Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph

Indiana Stangers Association
Buy your parts here
ICQ# 42269241
2FastLX is offline   Reply With Quote
Old 06-13-2001, 12:30 PM   #5
Shawn
Registered Member
 
Join Date: Dec 1998
Location: Chicago, IL. USA
Posts: 77
Post

Definitely sounds like vacuum leak, bent pushrods wouldn't happen from that..oils completely different system. Like the other post said, check the big line, also check so see if you put lines in the wrong places...get a manual if you don't have one. Brakes are vacuum assisted-so thats tied into the same situation. Also, smoke under hood, you might have just spilled something, does it smell like antifreeze or oil? Never had the problem on a car, but on a motorcycle once I didn't hook up a vacuum line and it seemed to burn oil, might have been pulled through the valve stem seal somehow? anyway...check lines! Someone above had stated spray WD40, this works forsure, but leaves a messy film all over! If you spray starting fluid around(not tons, this stuff can be dangerous) and the car revs, then you have a leak in the area you just sprayed.

[This message has been edited by Shawn (edited 06-13-2001).]
Shawn is offline   Reply With Quote
Old 06-13-2001, 12:36 PM   #6
DemonGT
Registered Member
 
DemonGT's Avatar
 
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
Post

i dont now what color the smoke was.....after work ill see what my buddy has found out and get back to you guys

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Waiting install:TFS street heat,Accufab TB

Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's
ICQ#35670781
DemonGT is offline   Reply With Quote
Old 06-14-2001, 12:56 AM   #7
93CobraR
Registered Member
 
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
Post

Also, are you sure you used the correct lower intake gaskets? and did the lower intake line up fine?
93CobraR is offline   Reply With Quote
Old 06-14-2001, 12:00 PM   #8
DemonGT
Registered Member
 
DemonGT's Avatar
 
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
Post

well worked on it yesturday and it started..but i had coolant not driping but pouring out the exhaust..tore it down and found the passanger side lower gasket had slide forward and was leting coolant throw..ordered new gaskets...

also..are you suppose to use that black liquid gasket stuff on the upper and lower intake gaskets to or just the cork gaskets?

------------------
'91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF

Waiting install:TFS street heat,Accufab TB

Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's
ICQ#35670781
DemonGT is offline   Reply With Quote
Old 06-14-2001, 12:16 PM   #9
fordgasm
Registered Member
 
fordgasm's Avatar
 
Join Date: Jan 1999
Location: Clayton, North Carolina, USA
Posts: 803
Post

You don't need gasket sealer on the upper intake, the lower you should use the RTV on the front and rear of the intake. Where the cork gaskets are located. I prefer to use just RTV and no gasket in this location, the cork ones tend to slip out occasionally. Use a large 1/4" bead if you don't use gaskets here. I like to use alignment pins so that when you lower the intake into place it drops straight down creating a good seal. I took 4 5/16 x 3" or 4" long bolts, cut the heads off and grind a radius on the ends to make alignment pins.

------------------
fordgasm
CLICK HERE to see my 87 GT
fordgasm is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Rocker adjustment zach0 Classic Mustangs 3 04-24-2004 12:28 PM
Edelbrock RPM intake install problems jruppert Windsor Power 4 03-04-2004 05:05 PM
Cobra Intake? 95mustanggt Windsor Power 5 10-01-2002 09:55 AM
upper intake and egr spacer install..... scale Windsor Power 3 08-18-2002 11:37 PM
new coolant leak after intake install fiveohpatrol Windsor Power 15 03-04-2001 09:15 PM


All times are GMT -5. The time now is 04:02 AM.


SEARCH