Misfire at low RPM

bigred90gt · 07-16-2002, 05:04 PM

I have a problem with my car misfiring at a low RPM. from about 1500 to about 2500 it misses. Once you ecxeed the 2500 it lines out. I have a 302 crate engine bored out to a 306, MSD 6al, 70mm T.B., off road X pipe, pullies, mac equal shorties, cold air intake, and 3.73's. I thought it was the itming, so I took it to a local speed shop and when they adjusted the timging, it did nothing. After I left the shop, it got worse. I replaced the cap and rotor along with the plugs, and now I am back to where I was. Any suggestions would be greatly appreciated.
This started after I installed the MSD, x-pipe, and the throttle body.

Ieatcamaros · 07-16-2002, 05:24 PM

Did you install the msd, x pipe, and throttle body at the same time? With all three of those mods, it could be any of them. Without knowing your car a little better, it is hard to pinpoint which one it would be. What did the speedshop set your timing at?

PKRWUD · 07-16-2002, 05:29 PM

I hate to say it again, but if wires #5 & #6 are touching at all, that could be your problem. It's worth the time to separate them.

Take care,
-Chris

Eric4Nitrous · 07-16-2002, 05:40 PM

I agree with PKRWUD on this one. Those are things that most people don't take into consideration. I would try that first before anything. If your timing is off even more it's gonna miss or backfire like crazy at low rpm's. Also, check the msd on that car. MSD has had some problems with that.

Eric

bigred90gt · 07-17-2002, 03:29 PM

My timing was set to 14 deg.

How would I go about checking the MSD to see if it is acting up? Disconnect it?

Eric4Nitrous · 07-17-2002, 03:41 PM

Yes just disconnet it and see if it's getting any spark to the number 5 and 6 cylinders.

07-16-2002, 05:04 PM	#1 (permalink)
bigred90gt 2 Stangs in the Stable Join Date: Apr 2002 Location: Baytown, TX Posts: 1,207	Misfire at low RPM I have a problem with my car misfiring at a low RPM. from about 1500 to about 2500 it misses. Once you ecxeed the 2500 it lines out. I have a 302 crate engine bored out to a 306, MSD 6al, 70mm T.B., off road X pipe, pullies, mac equal shorties, cold air intake, and 3.73's. I thought it was the itming, so I took it to a local speed shop and when they adjusted the timging, it did nothing. After I left the shop, it got worse. I replaced the cap and rotor along with the plugs, and now I am back to where I was. Any suggestions would be greatly appreciated. This started after I installed the MSD, x-pipe, and the throttle body.

07-16-2002, 05:24 PM	#2 (permalink)
Ieatcamaros Domestic Rice really sucks! Join Date: Apr 2002 Location: KY Posts: 973	Did you install the msd, x pipe, and throttle body at the same time? With all three of those mods, it could be any of them. Without knowing your car a little better, it is hard to pinpoint which one it would be. What did the speedshop set your timing at? __________________ The sig says it all.

07-16-2002, 05:29 PM	#3 (permalink)
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	I hate to say it again, but if wires #5 & #6 are touching at all, that could be your problem. It's worth the time to separate them. Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

07-16-2002, 05:40 PM	#4 (permalink)
Eric4Nitrous Registered Member Join Date: Jan 2002 Location: Va Posts: 1,122	I agree with PKRWUD on this one. Those are things that most people don't take into consideration. I would try that first before anything. If your timing is off even more it's gonna miss or backfire like crazy at low rpm's. Also, check the msd on that car. MSD has had some problems with that. Eric __________________ 68 Camaro Gene Fulton 632ci Two stages of Jug 8.41 164mph Rockingham 1-26-03

07-17-2002, 03:41 PM	#6 (permalink)
Eric4Nitrous Registered Member Join Date: Jan 2002 Location: Va Posts: 1,122	Yes just disconnet it and see if it's getting any spark to the number 5 and 6 cylinders. __________________ 68 Camaro Gene Fulton 632ci Two stages of Jug 8.41 164mph Rockingham 1-26-03

07-17-2002, 03:29 PM	#5 (permalink)
bigred90gt 2 Stangs in the Stable Join Date: Apr 2002 Location: Baytown, TX Posts: 1,207	My timing was set to 14 deg. How would I go about checking the MSD to see if it is acting up? Disconnect it?

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GM Engines	BLOCKER	Blue Oval Lounge	2	04-13-2004 01:35 AM
Speed Secret # 3	jim_howard_pdx	Windsor Power	13	11-09-2002 10:35 AM
Edelbrock RPM Package	jim_howard_pdx	Classic Mustangs	2	10-28-2002 04:57 PM
Experience with Edelbrock RPM Package	jim_howard_pdx	Windsor Power	0	10-27-2002 01:10 AM
RPM difference between 3.73 to 4.10	o2superstang	Modular Madness	0	07-09-2002 07:58 PM

Sponsored Links