This is my combo... What must I do to run 11's!?

jz_mustang50 · 09-30-2001, 12:19 PM

Ok... What I want to do is run 11's ALL MOTOR. No power adders. I want to keep my STOCK SHORT BLOCK and I'm staying with the AOD!!!!!!!! Tell me what more I need to do to my car. Check out my signature below to see what my car consists of. What I really wanted to do was just add to the motor, ie heades/intake/cam/injectors/maf/tb/torque converter. My next thing I'm doing is adding long tube 1 5/8 with 3 in collector headers so consider that done. Tell me what else I need to do! I have alot of opinions that very ALOT. I'd like to come to a conclusion about what will and what won't work before i DO IT.

------------------
Joe Zemaitis, Grand Rapids Michigan

1991 Mustang GT. Mods to date: 4.10 rear end, new POSI, aluminum driveshaft, AOD w/ shift kit, 2 1/2 off road h-pipe, 2 1/2 flowmasters and 2 1/2 tail pipes. Electric fan, Removed air pump and egr tube. Jegs brand upper and lower adjustable control arms. Removed back seats. Hoosier Quick Time Pro 27x10.5x15 and bolt on subframes soon to be welded. Everything else is STOCK. Totally stock ENGINE. 14.29@96 with 130k miles.

Skyman · 09-30-2001, 01:29 PM

Your going to need to make some serious power and serious traction to get that stock compressioned AOD car into the high 11's.

You will need good heads, a high revving cam, and intake to match it. DEEP gears, 410 or 430.l Full exhaust setup, and all the small supporting peices. If that short block has 130k you may want to think about rebuilding that also.

Your gonna need a high stall as 1.6x 60' are going to be necessary.

Not to mention traction devices and slicks.

Skyler

------------------
-1989 Saleen Mustang #406-
TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20.
12.54@107.4 Motor
332RWHP, 350rwtq

jz_mustang50 · 09-30-2001, 01:35 PM

To reply to skyman, I already have 4.10 gears and slicks (well... cheater slicks from Hoosier). I know that I'll need a high reving cam and big heads, but what cam, and what heads? I know the basics, and I have a combination in mind, but I'd like to know what everyone else thinks. Try to be specific please. :-)
Thanks!!

------------------
Joe Zemaitis, Grand Rapids Michigan

1991 Mustang GT. Mods to date: 4.10 rear end, new POSI, aluminum driveshaft, AOD w/ shift kit, 2 1/2 off road h-pipe, 2 1/2 flowmasters and 2 1/2 tail pipes. Electric fan, Removed air pump and egr tube. Jegs brand upper and lower adjustable control arms. Removed back seats. Hoosier Quick Time Pro 27x10.5x15 and bolt on subframes soon to be welded. Everything else is STOCK. Totally stock ENGINE. 14.29@96 with 130k miles.

Dark_5.0 · 09-30-2001, 05:46 PM

Well this guy that runs at the same track that I go to has the Holley systemax kit 4.30 gears all the suspension goodies a roll cage and slicks and he pulls off real high 11's.

------------------
88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft)

Rev · 09-30-2001, 06:52 PM

I'm worrying about a stock AOD with a shift kit withstanding 11's. Might ought to think about a Lenco.

Rev

------------------
'66 Coupe, 306, 300 HP, C-4, 13.97 e.t., 100.3 mph
1/4 mi.

09-30-2001, 12:19 PM	#1
jz_mustang50 Registered Member Join Date: Sep 2001 Location: Grand Rapids, Michigan, USA Posts: 50	This is my combo... What must I do to run 11's!? Ok... What I want to do is run 11's ALL MOTOR. No power adders. I want to keep my STOCK SHORT BLOCK and I'm staying with the AOD!!!!!!!! Tell me what more I need to do to my car. Check out my signature below to see what my car consists of. What I really wanted to do was just add to the motor, ie heades/intake/cam/injectors/maf/tb/torque converter. My next thing I'm doing is adding long tube 1 5/8 with 3 in collector headers so consider that done. Tell me what else I need to do! I have alot of opinions that very ALOT. I'd like to come to a conclusion about what will and what won't work before i DO IT. ------------------ Joe Zemaitis, Grand Rapids Michigan 1991 Mustang GT. Mods to date: 4.10 rear end, new POSI, aluminum driveshaft, AOD w/ shift kit, 2 1/2 off road h-pipe, 2 1/2 flowmasters and 2 1/2 tail pipes. Electric fan, Removed air pump and egr tube. Jegs brand upper and lower adjustable control arms. Removed back seats. Hoosier Quick Time Pro 27x10.5x15 and bolt on subframes soon to be welded. Everything else is STOCK. Totally stock ENGINE. 14.29@96 with 130k miles.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Thoughts on Combo?	Rosco	Windsor Power	9	06-03-2004 06:07 PM
Anyone here run a similar combo and if so, what times did it run?	slowfive0	Power Adders	3	02-02-2004 01:39 AM
Carb Combo	86GT	Windsor Power	8	08-24-2002 07:23 PM
Bad @ss 351w combo. need help	BowTie Eater 5 Liter	Stang Stories	2	02-28-2001 02:04 PM
BAD @SS N/A 351w Combo? (Long)	BowTie Eater 5 Liter	Windsor Power	0	02-27-2001 10:47 PM

09-30-2001, 01:29 PM	#2
Skyman I need 110mph Trap Speed! Join Date: Feb 1999 Location: So, CA Posts: 4,315	Your going to need to make some serious power and serious traction to get that stock compressioned AOD car into the high 11's. You will need good heads, a high revving cam, and intake to match it. DEEP gears, 410 or 430.l Full exhaust setup, and all the small supporting peices. If that short block has 130k you may want to think about rebuilding that also. Your gonna need a high stall as 1.6x 60' are going to be necessary. Not to mention traction devices and slicks. Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor *332RWHP, 350rwtq*

09-30-2001, 01:35 PM	#3
jz_mustang50 Registered Member Join Date: Sep 2001 Location: Grand Rapids, Michigan, USA Posts: 50	To reply to skyman, I already have 4.10 gears and slicks (well... cheater slicks from Hoosier). I know that I'll need a high reving cam and big heads, but what cam, and what heads? I know the basics, and I have a combination in mind, but I'd like to know what everyone else thinks. Try to be specific please. :-) Thanks!! ------------------ Joe Zemaitis, Grand Rapids Michigan 1991 Mustang GT. Mods to date: 4.10 rear end, new POSI, aluminum driveshaft, AOD w/ shift kit, 2 1/2 off road h-pipe, 2 1/2 flowmasters and 2 1/2 tail pipes. Electric fan, Removed air pump and egr tube. Jegs brand upper and lower adjustable control arms. Removed back seats. Hoosier Quick Time Pro 27x10.5x15 and bolt on subframes soon to be welded. Everything else is STOCK. Totally stock ENGINE. 14.29@96 with 130k miles.

09-30-2001, 05:46 PM	#4
Dark_5.0 Registered Member Join Date: Apr 2001 Location: Staging lane Posts: 4,337	Well this guy that runs at the same track that I go to has the Holley systemax kit 4.30 gears all the suspension goodies a roll cage and slicks and he pulls off real high 11's. ------------------ 88 mustang gt convertible bored to 306 BBk equal length headers, mac cold air fender kit, 3.73 FMS gears, Steeds Tri-ax shifter, Steeda underdrive pullies, Custom off road X-pipe, 2 chamber flow masters, cowl hood, nitto drag radials, ford racing clutch, 160* thermostat 16 degrees of timing electric fan off 94' t-bird jacobs electronics cap and wires. Edelbrock 1 1/2 inch drop springs. (Best E.T. 14.79@93mph @3000ft)

09-30-2001, 06:52 PM	#5
Rev Registered Member Join Date: Nov 1998 Location: Houston, Tx. Posts: 3,887	I'm worrying about a stock AOD with a shift kit withstanding 11's. Might ought to think about a Lenco. Rev ------------------ '66 Coupe, 306, 300 HP, C-4, 13.97 e.t., 100.3 mph 1/4 mi.